Tip 1: How to make glass tinting

Tip 1: How to make glass tinting

Tinting the car with your own hands will significantly reduce your costs for the car service and in addition will add skills in the transformation of your car. It also protects from harmful ultraviolet rays.

How to make glass tinting

You will need

  • - a roll of a tint film;
  • - putty knife;
  • - sharpened knife;
  • - detergent;
  • - Warm water;
  • - rags without lint;
  • - atomizer;

Instructions

1

Set the tint on the car's glass verysimple, but the process requires attention, patience and accuracy. When doing the work, you should call yourself a couple of assistants, for safety, to avoid any complications when sticking. Toning glasses should be done in a clean room or on the street in a calm. The most important requirement when choosing a film is compliance with its GOST. The fact is that the country has a law prohibiting the toning of the front windows, if the permissible darkening rate is exceeded.

2

Since the side windows are much easier to remove thanfront and rear, then you should start with them. Remove the door trim, while paying attention to the so-called clips, they are very fragile and therefore should be stocked with a new kit, as the probability of their damage is more than 70 percent. Then gently remove the glass from the door. Very carefully wash the window with a glass cleaner and degrease the surface with alcohol. Then attach the film to the glass with a dark layer inside. The main thing is do not confuse the parties. To avoid this, slightly disconnect the corners of the film. Next, align the tint and trim it so that the film's output beyond the glass is at least 1 cm.

3

Cut a piece of shape you want, then carefullypour it with a soap solution, which remained after washing the glasses. After that, it must be poured into the spray gun. This is necessary so that when the dark layer of the film is disconnected, you simultaneously wet it from this device. To do this, you will need helpers, one person will keep a transparent layer, the other will shoot and abundantly water the dark.

4

Now carefully smooth out the rubber orsilicone spatula arisen air bubbles. This procedure should be done from the center of the glass to its edges. Smooth until all bubbles disappear, then cut all the protruding edges of the tint film with a sharp knife. And in the completion of the work, dry the window with a construction hair dryer. After installing the tint film it is not recommended to open the windows for two days. And remember that doing toning yourself, you do not have any guarantees for the work done. And perhaps you will have to do this procedure more often than if you had contacted a specialist for an auto service.

Tip 2: How to make tint yourself

Summer heat forces drivers to look for ways tostruggle, aimed at reducing the degree of air heating in the car. The positive effect, pursued by the set goals, is achieved by self-toning the side windows of the body of the machine.

How to make a tint yourself

You will need

  • Film for toning, scissors, detergent, water.

Instructions

1

The flat surface of the side window is pastedtint film is not difficult. The only condition in the course of this work is the absence of various litter in the form of dust and grains of sand in the water and on the surface of the glasses.

2

At the first stage of performance of tinting worksit is necessary to make patterns for the subsequent raskroki self-glued tint film. The projection of the glass, intended for subsequent pasting, is removed on ordinary paper, and then similar patterns for the size of the pattern are cut out - blanks.

3

The glasses are washed with a detergent diluted in water, then washed under running water and laid out on a flat surface.

4

Then the surface of the glass is abundantly wettedan aqueous solution containing a small amount of liquid detergent (50 g of the preparation per 10 liters of water). Next, from the pattern intended for toning, the protective layer is removed, and it is gently applied to the surface of the glass.

5

Strictly aligning the edges of the film with glass, softrags, to avoid scratches on the film, from under it the remains of moisture are removed. And after a half or two hours of glass can already be installed on the regular seats of the body of the car.

Tip 3: How to Tint

Tinted windows lesssun rays into the interior and, as a result, objects that are in the cabin are heated less. Also, the tinted windows prevent the salon from viewing from the street, thus the objects inside the car do not attract thieves. If you want to protect yourself from unnecessary views, then toning in this will help you. The tinted car looks more beautiful.

How to make a tint

You will need

  • - Tint film;
  • - rubber spatula (spatula);
  • - 1.5 liter bottle with water spray;
  • - a knife (sharp blade);
  • - a ruler (a ruler);
  • - Industrial hair dryer (to eliminate bubbles and folds on curved glass);
  • - Foaming agent (shampoo, liquid soap);
  • - Scotch tape;
  • - A dry rag.

Instructions

1

The film should be chosen depending on yourneeds and in accordance with the law on toning cars. Do not use a cheap film for toning, it quickly burns out or peels off. Work in a dust-free room. If necessary, wet the floor at the work site with the film.

2

Toning in the showroom costs from 2000 rubles. By its own forces, it can cost you 400 rubles and a few hours. To do this, you need a desire and wit.

3

Remove and remove the glass from the vehicle. Put the glass on a wide flat place. Pour water into the bottle and add to it 4-6 drops of foam agent. Carefully clean the glass on the inside of the dirt and dust. If you have glued the old film, gently remove it with a blade or knife.

4

Find the side of sticking the film and attach toglass. Cut out the contour with an indent 2-3 cm from the desired size. Fasten the two lower corners of the film with pieces of tape to the table. Gently begin to separate the transparent film layer. Spray a lot of tint film with a soap solution.

5

Attach half of the film to the glass and completely remove the transparent layer by peeling off the adhesive tape. Always make sure that the film and glass are well-watered. Align the film over the glass.

6

Rubber spatula begin to expel liquidfrom under the film. Start from the center to the edge of the glass. Make sure that the film does not have blisters. Be careful. If necessary, use a dry rag.

7

Dry the glass with a hairdryer. With a knife or a blade, cut off excess film by the ruler (pattern). Put the glass back on the car. It is recommended to open the window after 24 hours.

0