Tip 1: How to cut a brick

Tip 1: How to cut a brick

There are two ways with which you can cutbrick. In order to do this qualitatively, you need to know the rules of working with this material. This will avoid cracking the stone and getting injuries during the sawing.

You can cut the brick with the help of Bulgarian
Brick is a very pliable material. It can be processed so figuratively that it will become a decoration for a stove or walls. The building can not be built only from a whole brick, so you need to learn how to cut it.

How to cut a brick circular?

With any method of processing this constructionIt should be taken into account that a lot of dust is formed during the sawing process. Therefore, it is better to work outdoors, periodically wetting the brick with water. This will allow you to breathe clean air and do not use a respirator. But in any case it is recommended to wear protective goggles. The cookers soak the brick in water before starting the treatment for a day. But for construction work this is not necessary and is not always possible. With a circular saw, you need to remove the standard saw blade and cut an abrasive wheel made of fiberglass. In the trading network, they can be called "for cutting steel." The diameter of the circle should be such that its cutting edge protrudes above the circular table by at least 7 cm. This condition must be observed, since it will greatly facilitate the work. The cutting part of the circle should be larger than the standard brick thickness (6.5 cm), but not much. The cutting process for this material is practically the same as sawing wood. On the circular, you need to set the required size with the help of the bounding ruler, turn on the saw and slowly bring the brick to the rotating circle. If the circular is hand-made, the brick must be laid beforehand so that it is convenient to saw. For example, on two wooden bars between which there must be a distance required for the safety of work.

Cutting bricks with an angle grinder (grinder)

This tool is traumatic, so working withthey need to be neat and in a state of complete concentration. Inevitable satellites of the process of cutting - scale, abrasive particles, sparks. Therefore, it is not recommended to remove the protective cover from the instrument and operate without glasses. To cut the brick, you need a special circle, which is designed for stone processing. Before starting the sawing, you need to make sure that the disk does not have chips, cracks or potholes. Cutting the brick is necessary, taking a stable position and smoothly bringing the working tool to the side edge of the stone. After that, you need to slowly make a longitudinal incision and gradually deepen into the thickness of the brick. The main danger in this work is a back blow, which is expressed in the sudden rejection of the Bulgarian because of the jamming of the disk. To avoid unpleasant consequences, it is necessary to adhere to the safety rules for working with this tool.

Tip 2: How to know the weight of a brick

Brick is a building material thatIt is made of clay by the method of roasting or steaming. Depending on the type and scope of application distinguish ceramic, silicate and facial bricks. To make the calculations necessary for transportation bricks, it is necessary to know its dimensions and the weight.

How to know the weight of a brick

You will need

  • - a metal ruler;
  • - calipers;
  • - square;
  • - calculator;
  • - a sheet of paper for data recording.

Instructions

1

The weight bricks directly depends on its dimensions: length, width and height, as well as the density of this building material. Weight bricks is calculated by the product of the product of volume bricks On its density.

2

Measure with a ruler the width, length and height of one bricks. Record the measurement results on a sheet of paper in millimeters.

3

To determine the curvature of the edges and surfaces, attach the edges of the square or metal ruler and measure the maximum convexities and deflections.

4

To identify broken edges or corners, determine the difference between the required size bricks and the whole parts of each of the edges that make up the angle.

5

Multiply the resulting width, length, and height with each other to get the volume bricks. Data on the density bricks ask the seller or the manufacturer of this building material. Standard density bricks Is equal to 1800 kg / m³.

6

Multiply the density by volume. The result obtained is the bulk density bricks.

7

You can define the weight bricks Through technical the weights. To do this, put the sample on the the weights and write down the testimony. The brick must first be dried to a constant the weighta.

0