LovesTheTeam.com

You will need

• Soap, Novost powder, hydrogen peroxide, ammonia, turpentine, dry chalk, dry clay, onion, whey powder, blotting paper, iron

Instructions

1

Mold on white woolen, linen and cottontissues that can be washed, removed with soap or powder "News". After washing, bleach the product with hydrogen peroxide at a rate of 1 tablespoon per 1 liter of water. A liquid ammonia (a teaspoon per glass of water) is also suitable.

2

Another way to get rid of mold stains onCotton cloth - cover the stain with a thin layer of crushed dry chalk. Place blotting paper on top and draw a warm iron several times at the location of the stain.

3

Stains from mold on silk and woolen fabrics,not subject to washing, remove with turpentine. First, peel the stain with turpentine, then cover with a thin layer of dry clay. The iron comes to the rescue again - iron the fabric through blotting paper. If the cloth is white, soak the stain with hydrogen peroxide, then stretch the product and rinse it in warm water.

4

Color and dyed fabric, touched by mold,treat with ammonia. Before you moisten the stain with ammonia, try on a separate piece or in an inconspicuous place on the wrong side to make sure that the alcohol does not change the color of this fabric.

5

It is easiest to remove fresh stains from mold. To do this, wipe the stain several times with the juice of onions or serum curdled milk. After the treatment, wash the product in hot water.

You will need

• - a hard brush or spatula;
• - composition for removal of cement film and opening of pores (all materials can be purchased in construction shops);
• - antiseptic dry soil to remove mold;
• - Brush or roller;
• - antiseptic primer of deep penetration (for priming the wall);
• - dry waterproofing mixture;
• - plaster;
• - heat-insulating paint;
• - putty;
• - New wallpaper or paint.

Instructions

1

First, you need to find out the reasons whythis mold appears, so that this does not happen again. Knowing the reasons, you can easily find a way how to get rid of it. Most mold appears due to high humidity and condensation. Only from dampness it can not appear. Condensation appears due to high humidity in the room, caused by poor ventilation and plastic windows. Dampness on the wall and high humidity in the room can appear due to the marriage in the construction: the inter-panel seams are poorly insulated, the residual moisture of the materials is increased. As a result, the humidity in the apartment can increase even oblique rain in the wall.

2

When the causes are revealed, proceed to deliverancefrom the mold itself. There are many materials and tools that help to get rid of it, but it is best to repair the room or even the entire apartment, as the mold fungus is most likely to be found everywhere. Remove the wallpaper. With a stiff brush or spatula, remove the affected areas of the plaster with mildew. Peel off that layer of plaster where it has become loose. Walls should be treated with a mold remover. Antifungal agent dilute with water. The received structure put on walls a brush or the platen. You need to treat all the walls, not just those affected by mold.

3

Prime the walls with antiseptic primer. Prepare a waterproofing compound. Apply it to the walls with a brush or roller. Once again, pound the walls. Carry out the plastering of the walls. Apply thermal insulation paint. Carry out the putty surfaces. Again, primed the walls with antiseptic primer. And only after that, paste the wallpaper or paint the walls.

You will need

• - potty;
• - soil;
• - expanded clay.

Instructions

1

The easiest way to destroy mold in flower Is to change the whole ground. In this case, the plant is carefully removed from the pot, the roots are freed from soil debris and spilled with a weak solution of potassium permanganate. The old soil can only be used if it is baked in an oven at high temperatures. This will remove the soil from excess moisture and destroy spores mold. As a preventive agent in the kidney, activated carbon is added.

2

Before pouring the soil into the pot, the lastalso it is necessary to stand in the oven or to give boiling water. This is possible only with ceramic pots, if the mold appeared in flowers growing in plastic, then it is impossible to guarantee the absence of fungus spores in the container itself.

3

To prevent mold from appearing in flowersfurther, make a qualitative drainage. To do this, mash at least 1.5-2 cm of claydite on the bottom, and already lay the soil on it and root the plant.

4

The top part of the pot can be covered with a layer of sandor expanded clay, on them the mold is formed much less often. In the event that the mold does appear, it is enough to rinse and calcify the expanded clay or replace the sand.

5

It is much easier to prevent the emergence of mold, than to fight it. Therefore, take as a rule ignite the newly acquired or collected in the forest soil, which is planned to transplant the plant. This will avoid infection of the soil with spores mold.

You will need

• - lemon acid;
• - table vinegar;
• - detergent with chlorine content;
• - 50% solution of copper sulfate;
• - bleach;
• - soda;
• - UV lamp;
• - The steam generator.

Instructions

1

Citric acid helps to get rid of mold. Take three tablespoons of acid and pour them into the powder tray. Turn on the washing machine in rinse mode.

2

Mix a liter of table vinegar with the same amount of detergent containing chlorine. Pour the mixture into the powder tray and turn on the machine, selecting the highest temperature for washing.

3

Quite often, traces of mold can be seen in the powder tray. Therefore, you must necessarily clean it with a hard brush and any detergent.

4

Most often the fungus appears on the cuff -rubber trim around the door. Therefore, you need to thoroughly clean it. For this purpose, means that contain chlorine are suitable. Wash the cuff thoroughly with a solution, then turn on the rinse mode.

5

A 50% solution of copper sulphate can help in the fight against mold. Thoroughly treat this substance with rubber parts of the machine and leave it overnight. In the morning, rinse with soapy water.

6

Remember that mold loves moisture. Therefore, after each wash for 2-4 hours, leave the washing machine door and detergent tray slightly ajar so that all parts can dry completely.

7

After each wash, wipe the cuff dry - this will help prevent the formation of mold.

8

If no methods work, then you need to disassemble the machine and carefully treat all parts with bleach, soda or other cleaning agents.

9

To completely destroy the mold, you can use an ultraviolet lamp.

10

If possible, then process the detailsmachines with a steam generator - at such a high temperature, fungi die. It is desirable that this procedure involved a specialist in the repair of washing machines.

11

Sometimes fungi so strongly eat into the cuff that it is almost impossible to get them out. In this case, it must be changed to a new one.

You will need

• - respiratory mask;
• - latex gloves;
• - putty knife;
• - building antiseptic;
• - cleaners with chlorine;
• - hydrogen peroxide.

Instructions

1

The main causes of occurrence and spreading mold in the house - high humidity and badventilated rooms. Check how the extractor works: the sheet book attached to it should not fall. Otherwise, contact the utility with a request for repair. Plumbing should not leak, and pipes should be wet. If you have plastic windows, ventilate the room twice a day. Between walls and furniture when installing it, always leave a small space so that air can easily pass.

2

To get rid of the fungus on the walls, removeold wallpaper in the hearth lesions. Do not forget to wear a respiratory mask, which will protect the respiratory organs from penetration of spores. With a spatula, remove all areas of paint and plaster where the fungus was. Then, treat the whole wall with an antiseptic to prevent the appearance of mold further. Before buying, consult with a consultant, which tool is right for you, because for each type of fungus there is a drug. When the product is absorbed, apply an antiseptic primer to the wall to level it. And only after the surface dries completely, you can start plastering and wallpapering. At the end of the work, ventilate the room and dry the wall, and only then put furniture to it.

3

Mold in the bathroom can be overcome withcleaning agents, the main thing is that they contain chlorine. For example, dilute the bleach with water in a ratio of 1: 1, and then apply the solution to the foci of fungus. After a while, rinse these places with a damp sponge or rub with a stiff brush. Rinse with clean water.

4

With mold on silk or woolen fabricwill cope with turpentine, which must be applied with cotton wool to the affected area of ​​the canvas, then sprinkled with clay, wrapped with a paper towel and ironed with a warm iron. Only after this, the product can be washed. With white tissues remove stains from the fungus, using chlorine or hydrogen peroxide, and with colored - ammonia.

5

Mold from books can easily be removed with a formalin solution applied to a cotton pad. To prevent the fungus from appearing in the breadbox, put a cotton swab dipped in it with iodine.