LovesTheTeam.com

You will need

• On a single-tiered cage for a pair of rabbits:
• Board or thick plywood 0.2 square meters. m
• Square frame for the frame
• Fine-meshed metal mesh with cells 18x18 mm - 1.3 m 2
• Metal mesh with cells 35x35mm - 0.6 square meters. m
• Reiki 3 cm wide
• Door hinges - 2 for the roof, 1 for each door.
• Door hooks or latches
• Ruler
• Pencil
• Saw
• Ax
• Sandpaper
• Hammer, nails, joiner's glue

Instructions

1

Start with the skeleton. To do this, mark and cut the bar into pieces of the required length. You need 4 racks of each size. Screw a rectangular parallelepiped out of pieces. From the plywood sheet, cut rectangles equal in size to the back and side walls. Sew them the frame from the outside.

2

Cut a rectangle from a fine mesh grid, bydimensions corresponding to 2/3 of the area of ​​the cell. Nail it to the lower beams of the frame so that it joins one side of the cage - this will be the stern compartment. For the nesting compartment, make a solid wooden floor.

3

Between offices it is necessary to deliverseptum. It is made from a rectangular sheet of plywood, in size corresponding to the width and height of the cage. In the middle, drill a hole in order for the rabbits to pass freely there. Saw two slices from the slats, equal to the length and width of the cage. Saw the corners so that when the rails are connected at a right angle there are no gaps. Nail the slats over the mesh along the inner perimeter of the cage.

4

From a sheet of plywood or boards make a roof. It should be slightly wider and longer than the cage, about 3-5 cm on each side. On one side of the frame, attach the door hinges.

5

Make the doors. One of them is wooden, it is designed for nesting. Its length is about 1/3 of the length of the cell. For the stern section, make one or two doors from a large mesh and slats. First, make a door frame from the rails, then attach a metal mesh. Hang the doors on the door hinges. Attach the hooks or locks.

Instructions

1

The floor grate should be cleaned withmetal scraper. Under the cage is placed a low capacity (for convenience it can be installed on a cart), into which the remains of food and litter are raked. Next, you need to raise or completely remove the lattice from the cage and remove the manure from it. That rabbits do not interfere during harvesting, they can be moved to the next compartment of the cage, after which it is necessary to close the lag with a plywood bolt. Thus, all cells are cleared, and finally the sex of the rabbit is swept.

2

The cleaning process will be accelerated if under the floorgrate the pallets from plywood or tin. On them will fall between the racks of the grate manure. If the pallet is made of wood, its bottom should be covered with polyethylene film, which protects the boards from swelling, and plywood from the bundle.

3

Initially, the cell lattice should be cleaned, andthen - push the tray and shake out the accumulated manure in a container. You can do this and through a special hatch in the wall of the rabbitry, from where the waste will fall directly into the compost pit, specially arranged outside the barn.

4

A couple of times a year, especially in the autumn and springtime, can not do without disinfection of cells. This procedure can be carried out in different ways. The simplest and most effective of them is the processing of the rabbit with fire. For this purpose, a gas burner or blowtorch is suitable for cleaning the cleaned wooden parts of the cage until lightening. During this procedure, it is important to be careful not to cause a fire.

5

You can disinfect the rabbit withchemical substances. In case of using bleach, a 10% solution is taken, which with the help of a wide brush processes the cells, equipment and walls of the rabbit.

6

Excellent kills germs of ash lye. To prepare the solution in boiling water, wood ash is added (at the rate of 1/3 of the volume of water). The mixture boils for about half an hour, after which it is filtered and again brought to a boil. Then immediately with a hot solution, you should start to process the cells.

7

Whichever method of disinfection would not be applied,the outer parts of the cells are periodically recommended to cover with a solution containing slaked lime. Wooden feeders are useful to handle the fire of a blowtorch, and the components of ceramic, glass, metal autocouples and autopilots should be better boiled.

Preparation and arrangement of the pit

Population of rabbits and further care

You will need

• For the removal of the frame will require bars of strongwood species. As a floor it is necessary to use a grid with the sizes of cells of 1.7 cm - 2 cm. For ventilation and air access on the front side of the cell, plastic or wooden slats up to 3 cm wide will be required.

Instructions

1

Before the beginning of construction it is necessary to determinethe size of the future cell. In the case of large animal breeds, the length of the cell will be 1.5 meters with a width of 70 cm and a height of about 50 cm. Average rabbits will be sufficient cells with dimensions of 90x60x45 cm.

2

For the construction of the cell will require trainedbeforehand material. As a cell wall, it is advisable to use boards or thick plywood. All material must be carefully processed and sanded.

3

Now you need to collect the cage. The work begins with the assembly of the framework. At a height of 70 cm, bars are knocked down at the corners of the cell in the form of a box. Preliminarily fixing the four supports, which serve simultaneously and lateral ribs of the future cell. Mounting can be both in the ground and in the wall of the adjoining structure. The frame is assembled in such a way that the height of its front part is 55 cm, and the back 35 cm for pitched roof.

4

It is necessary to cover the cage, leaving an empty roof andtwo openings for doors from the edges of the front side of the cage. By dividing the cage into a nest and aft compartment, the floor in the stern is sewn with a fine mesh net, and in the nesting board. The compartments are separated by a partition with a cut out hole for the manhole. The septum is attached to the walls of the cell.

5

Doors are made for both offices andhang on the hinges. The roof is made similarly. The door to the entire size is attached to the back wall of the cage. In this case, the task is to make the cage for the rabbit as easy to use as possible. For the convenience of feeding, the door in the stern compartment can be made from a grid with an attached feeder on the outside in the form of a box. The cage is ready.

You will need

• Veneer sheets
• Reiki
• Grid
• Saw
• Nails
• A hammer
• Fittings (hinges, handle)
• Ceramic bowl
• Special drinker
• Straw or shavings
• Newspapers
• Bar from fruit tree

Instructions

1

Make plywood billets for the side walls of rabbits Small housebut depending on the size of the pet. You should have squares of at least 70 by 70 cm. The back wall will be no less than a meter in length; in height, it should be 15 centimeters below the sides. This is necessary in order to place a pallet under the cage. The house will stand on the "legs" - the side walls.

2

Slam Small house for a rabbit, for stability using rails. Strengthen the three walls; and for a facade and a flooring use a strong grid with small apertures. Meter bars fix the mesh rectangles; and, at the top edge, nail the bar with the future cover-door.

3

Render the rabbit's roof Small houseand from the net and racks and hang it on the back wall withusing two metal loops. In the middle of the front edge of the lid, set a comfortable handle - so you can easily open and close the rabbit Small house, clean it and put food.

4

Equip the cage for a rabbit all necessary:• Place a plastic pallet of the appropriate size under the bottom grid • Cover the mesh floor of the box with oat straw (or several layers of newspaper and large wood shavings) with a layer of at least 2 cm. • Place a heavy bowl of pottery for food so that the animal can not easily overturn it. • Attach a special drop drip to the rabbit cage for pets. Small house for a rabbit A clean bar made from solid fruitwood so that your pet can sharpen teeth.

You will need

• Spacious cage, sawdust for bedding, nursery with fresh hay, drinker with water, toilet for rabbit.

Instructions

1

Consider that live on the trellised floor rabbits are not adapted, because unlike cats and dogs they do not have pads on their paws. So choose cage It costs with an even floor or just put onlattice floor cells a pair of boards for resting the animal. Otherwise, your pet will spend most of the time in the toilet tray simply because it is easier for him to sit there.

2

Choose for a rabbit cage large size: the size of the cell at least 4 times must exceed the size of the animal. This is the case if a rabbit let out of it to run. If he lives in it constantly, then an even more spacious cell will be preferable. You can buy for a pet multilevel cage - he will, where to jump and warm up. It should be taken into account that rabbits grow very fast, so you can buy immediately cage the size of about 100 cm (this does not apply to dwarf species, although they will be happy with spacious housing).

3

Accustom your pet to a new spacious cage gradually, if before he lived in a cage of smaller sizes. You can put a small cage inside large and thereby, without injuring a rabbit, accustom him to a new place of residence.

4

Place cage at the level of the knee on the stand. Make sure that the heating batteries and the window with its falling direct sunlight are away from the animal - rabbits are very sensitive to high temperatures, but low (minus) carry with ease. Drafts and damp indoors are the enemies of this animal, as they are dangerous to his health.

5

Place it in cage A drinking bowl for rodents, a feeding bowl, a bowl forfresh hay and a house for rest and pet sleep. If you hang a special mineral stone for rodents (it can be bought at a pet store), it will create additional conveniences for the eared pet.

6

Put in cage toys for a rabbit: cardboard boxes (in them animals likeclimbing and gnawing them), twigs from the apple tree (but not cherry, apricot and peach, as they are poisonous for rabbits), special toys from the range of pet stores, pieces of cloth.

7

Do cleaning in a cage a rabbit daily. When he learns to walk into the tray, cleaning can be done less often. Every day you need to change the old food with fresh water. Disinfect the solution with potassium permanganate monthly.

You will need

• • 1 kg of rabbit meat;
  • 0.5 cups of milk;
  </ li>
  • 100 g of bacon;
  </ li>
  • 1 egg;
  </ li>
  • bread;
  </ li>
  • salt;
  </ li>
  • breadcrumbs;
  </ li>
  • double boiler.
  </ li>
  </ Ul>
  
  
  

  Instructions

  
  
  
  
  

  1

  
  

  Rinse the meat with cold water. Wipe with paper towels. Separate the meat from the bones.

  
  
  
  
  

  2

  
  

  Soak a piece of bread in the milk.

  
  
  
  
  

  3

  
  

  Pass the meat through the meat grinder along with the soaked bread and bacon.

  
  
  
  
  

  4

  
  

  In the mince, add the egg, salt and mix well.

  
  
  
  
  

  5

  
  

  Form small cutlets. Roll in the breadcrumbs. Bon Appetit!