Tip 1: How to remove the radio
Tip 1: How to remove the radio
The standard audio system of most cars is notsatisfies the requirements of avid music lovers. Therefore, there is a desire to install a new car stereo. But for this you need to remove first remove the standard head unit. This procedure for many car owners is difficult.
You will need
- - a special set for removing the radio cassette;
- - cotton gloves;
- - manual;
- - building hair dryer;
- - new cladding
Instructions
1
Open the bonnet and remove the negative terminal from theBattery to de-energize the on-board power system. This precaution, because when you remove the radio, you can accidentally close the wires. Read the instruction manual of your vehicle carefully. It may indicate the description of the process of dismounting the radio. If you do not have a printed version of the manual, then you can download it electronically. You can also get a basic knowledge of the audio system of your car by studying a special forum dedicated to your model.
2
Remove the facing parts. Usually they are plastic pads that cover the nests of screws and give the dashboard a more aesthetic appearance. The cladding is secured using plastic latches or pins. To remove it, you need to gently pull one of the sides to disconnect the mounts. Be very careful. If you bought a used car, the previous owner could glue the lining. This is the case when the latches are broken. If you find that your liner is glued, you should gently heat it with a construction hair dryer to melt the glue. Then gently uncover the plastic and maximally clean the space below it. Facing you need to buy a new one.
3
Take a special tool for dismantlingradio cassettes. Now they sell both universal sets, and adapted for a certain model. Remove all screws holding the frame. Also, you need to unscrew the screws of the adapter if you have a one-way radio. Insert the special tool from the kit into the holes and press it as far as it will go. The radio tape recorder must exit the internal socket. Sometimes it is necessary to dismantle the glove box to gain access to the rear side of the socket into which the radio is inserted. This allows you to push the radio in the back. Carefully remove the housing. Disconnect all cords of wires from a radio tape recorder. In doing so, try not to drop the wires in the hole, as getting them from there is very problematic.
4
Contact the nearest car repair shop if you are nothave the necessary skills to remove the radio. It is also worth contacting professionals in the event that at any stage you understand that you can not complete the procedure yourself. You will be happy to help remove the old audio system and install a new one, as well as provide a warranty on the work performed.
Tip 2: How to remove the radio from BMW
Every year manufacturers of car recorders introduce new models and modernize old ones. Proceeding from this, the BMW owner wants to replace the outdated radio tape recorder new model, but there is no knowledge and experience in self-installation. Often, the owner can not even remove the staff radio tape recorder. The radio tape recorder or radio receiver of the factory setting has a different mount. Before removing the radio, be sure to disconnect the ground wire (negative) from the battery.
You will need
- Screwdriver Set.
- Specialized keys for removing the radio cassette.
- Pullers.
Instructions
1
Radio receiver (radio) of the factory setting withThe retractable fastening can be quickly removed or installed only with a special key. Get such a key in a specialized store, if it was not attached to the radio while buying. You can recognize the quick-detachable attachment by two or four holes in the front panel. Depending on the power and number of speakers in the trunk under the lining on the left side, there may be an additional amplifier.
2
To remove the radio tape recorder type "Bavaria / C", remove bothcontrol knobs and decorative washers under them. With a narrow screwdriver, bend up the locking springs. They are located on the axes of the handles. Then remove the front panel and insert the tabs on the back of the panel into the slots. Note: the pressed out protrusions of the locking springs must be at the top and point to the front side of the panel. Then unscrew the screws located near the axes of the control knobs and remove the mounting brackets. Take out radio tape recorder from the dashboard. On the reverse side of the radio, find and disconnect the connectors of the mass, battery (B +), speakers, antenna and its electric drive (if any).
3
For removal of a radio tape recorder of type "Bavaria Cassette III"Or "Europe Digital" with a retractable fixture, find the two holes on the front panel on the left and right. Insert the pullers into these holes. If there are no such holes, remove the control knobs and panel, and then insert the pullers into the free holes. Pressing the pullers towards the outside of the panel, release the latches. Then take out radio tape recorder From the instrument panel, avoiding distortions while doing so. Before disconnecting the speaker connectors, mark the connectors of the left and right channel with something. For example, tapes of different colors. To remove the pullers, press a small screwdriver onto the spring clips.
4
Removing the radio tape recorder type "Bavaria Electronics"carry out in the following order. With a narrow screwdriver, gently bend the front panel. Remove the handle. Locate the clamps on the left and right of the panel and insert the keys to remove the radio. Pressing the keys towards the inside of the panel, take out radio tape recorder. Disconnect all connectors on the rear panel of the radio, including the antenna cable.
