LovesTheTeam.com

Instructions

1

Turn on the car stereo. If "SAFE" or "CODE" appears on its display, it means that the device has a system failure. In order to continue to work with the radio and enjoy the music, you must enter the correct code.

2

Take the instruction manual of the radio,which was in the delivery package of the device. The first page should contain the identification number next to which is the radio card. When buying a radio receiver, it is desirable to take it out and put in storage in a safe place, which should not be in the car itself, as this will facilitate the robbers hacking the device. So, take this radio card and remember the code.

3

Press the radio buttons simultaneously DX and FXAfter you see the inscription "SAFE" or "CODE". Hold them pressed until "1000" appears. Release the buttons and do not click on them anymore, because the system will accept this set of digits as a code.

4

Enter the code number from the radio card using the radio station selection buttons. Button 1 is responsible for the first digit of the code, button 2 for the second, and so on. Do not use buttons 5 and 6 during input.

5

Press the DX and FX buttons after entering the code forUnlock the radio and hold them until "SAFE" appears. As soon as it appears, release the buttons. The device will "think" for a while, after which the frequency of the radio stations will appear, which will indicate the release of the radio. If the code number was entered incorrectly, the word "SAFE" will blink for a while. After it lights up constantly, you will have another attempt to enter the code combination. If three times in a row the wrong order of digits is entered, then the radio is locked for an hour. Wait for this time, then try again.

Instructions

1

Audi Concert Plus (Blaupunkt) After turning onAnd press the RDS and TP buttons simultaneously and hold them in the same position until the number 1000 appears on the display. Enter the code using the buttons 1, 2, 3 and 4 and press again for 2-3 seconds , RDS and TP buttons.

2

Audi Gamma CC (Matsushita) Press simultaneouslyButtons M and U after SAFE. Hold them down until you see the number 1000 on the display. Enter the code, and then press and hold the same buttons again for a few seconds.

3

Audi Navigation Plus (Blaupunkt) Turn on the powerMedia system and select the code using the control dial. After the first digit of the code is entered, confirm it by clicking on the wheel. Enter and confirm the remaining digits in the same way. Select OK in the menu and press the control dial.

4

Audi Gamma CD 4A0 (Blaupunkt) After appearing onSAFE display, press the DX, U, M buttons in the specified sequence. Hold them for at least 5 seconds until the number 1000 appears. To enter the first digit of the code, use the number 1, pressing it repeatedly will select the digit from 0 to 9. To enter the second digit of the code, use the 2 button, etc. After the code appears on the display, press the M, U, and DX buttons strictly in the indicated sequence and hold them for a few seconds until SAFE appears. In a couple of seconds after this, the radio is ready to go.

5

To enter the code for the radio series gamma, beta andDelta, press and hold the DX and FM ½ keys. To access the input to the chorus, concert and symphony series, press and hold the RDS and TP keys.

You will need

• - Key Collector;
• - access to the Internet.

Instructions

1

Download the program Key Collector. It is worth noting that this application is paid, but it is worth the money spent on it. You can buy it at various specialized sites or online stores. In this case, beforehand, verify the reliability and decency of the source. Install the program on your computer and start to use.

2

Check if the topic of your resource is geo-referenced. To do this, open the "Regions" section and set the necessary check parameters.

3

Make a list of keywords and phrases. Go to the "Keywords" section and click the "Add" button. A window for entering the original data appears. After all the words are indicated, click on the "Add to Table" button. As a result, you will receive information about the frequency of use of certain combinations on the site, the location of the site in the issuance positions and the relevant pages for Google or Yandex.

4

Click on the button "Batch parsing with Yandex.Wordstat "to set phrases and words for statistics. Write several phrases in the window that opens, then click on the "Parse" button. After this, the program will take some time to process the process and collect data. As a result, you will receive statistics for the formation of the semantic core of your site. Dismiss the phrases-pacifiers, which have incorrect formulations or are requested only a few times a month.

5

Find out the exact frequency of key phrases. To do this, click on the button "Pursing the frequencies of Wordstat for available key phrases". Select the item "Refine the frequencies"! ". Thus, you can weed out those phrases that are almost not requested, and learn the real picture of the shows.

6

Clarify the correctness of word forms. Click on the button "Checking the correctness of word order", which displays statistics based on search suggestions. As a result, you get specific answers "Yes" or "No".

You will need

• - radio cassette recorder
• - Keycode (if any)
• - the serial number of the radio cassette
• - Thin metal objects
• - special program
• - documents for the car

Instructions

1

If the radio tape recorder is new, when it is first turned on, itCan behave differently (depending on the model): immediately display the word CODE or start a countdown. In the second option, wait for the time to expire. Press and hold for a period of 3-5 seconds a certain button (usually, 6 or a variant with two buttons: 6 + 1). The display should display the word CODE.

2

Enter the four-digit keycode. Usually it is issued together with the radio. Press "1" several times until the desired number appears on the panel. To dial the second digit of the code, press "2". Following "3" and "4". Look carefully so that all the digits coincide with the keystick.

3

Press "5" to confirm when the panel displays the correct code. After the done actions the radio tape recorder will turn on, and you can enjoy your favorite music! Be sure to write down the keycode.

4

When the battery is removed, the radio automatically turns off. In this case, you will need to re-enter the code. If it is lost, pull it out radio tape recorder from the nest.

5

On the side panel of the device must be a special label. It shows the serial number. Usually, it starts with a letter (often M).

6

There are several programs for selectionLost code. Download your favorite from the Internet, install on your computer, open it. Enter the serial number. The program selects the code. How to enter it in radio tape recorder - steps 1-3.

You will need

• - radio cassette recorder
• - instructions for radio tape recorder
• - code

Instructions

1

Read the instructions. On the first page there should be a detachable sheet with the code for the radio tape recorder - 4 digits, which you will need to enter into the system.

2

Turn on radio tape recorder. The screen will show SAFE. If you do not exactly know the model of the radio, study it for the presence of certain buttons. Depending on the presence / absence of designations, you will be able to navigate what to press next.

3

Press the DX and FM buttons simultaneously. Hold them until 1000 appears. Enter the code with 1-2-3-4, repeatedly pressing each key. The required figures must be displayed on the screen. Compare them with those that you have recorded. If everything is correct, press DX and FM again, hold for 2-3 seconds. The radio tape recorder will turn on.

4

Hold down the TP and RDS buttons. Wait until the number 1000 appears. Use the 1-2-3-4 buttons to enter the correct code. After an additional code check, use TP and RDS to confirm (2-3 seconds).

5

If there is no TP symbol, look for the SCAN button. When the display shows SAFE, hold both SCAN and RDS at the same time until 1000 appears. Enter the code with 1-2-3-4. To confirm the selection, press SCAN and RDS (2-3 seconds).

6

Press and hold the M and VF button combinationseither M or U. The display will show 1000. Enter the code with 1-2-3-4. To confirm, press and hold for 2-3 seconds the original combination of buttons.

7

In the Audi range is AudiNavigation Plus. Turn on the radio. Use the rotary knob to select the digits of the code. When the desired figure is found, click on the handle. Do the same for the other digits. When the code is entered, find the OK in the menu. Press the knob again to confirm. The radio tape recorder will turn on.

8

To enter the code in the car radio Audi Gamma CD 4A0035196NP2 AUZ5Z5 (Japan, issue 10.91) use the following sequence. Strictly keeping order, press DX + U + M. Hold for 5 seconds until 1000 appears. Enter the code in 1-2-3-4 digits. Use the combination DX + U + M to confirm (5 seconds). SAFE will appear first, and in two seconds the radio will work.

You will need

• - car
• - radio cassette recorder
• - instruction
• - Keycode

Instructions

1

In the instructions to the tape recorder, on the very first page, find a tear-off coupon with a recorded keystick. Rewrite it or take it with you to the car.

2

Turn on radio tape recorder. The display will show a word or characters thatwill be asked to enter a known code. Depending on the model, the following basic notations are displayed: "code" (flashes the letter c), "enter code number", "code ****", "1 - - - -", "safe".

3

With the word "code" with the flashing letter c, inputis carried out in two ways. First, when you have a keypad. In this case, directly dial the digits of the code. Those. Click on the buttons corresponding to all five code numbers. To confirm, select one of the following symbols: rds,> i,>, sc (depending on the model). The second way of input is with the help of the right twisting knob. Turn the dial to the correct number. Press the knob to confirm the selection. And so for all five numbers. If the entered code is correct, then the radio will start automatically.

4

When the display shows "enter code number",The code is entered directly. Alternately, press the buttons with the corresponding numbers. Make sure the number is correct on the display. To confirm, use "

5

If "code ****" appears, then you need to enter the digitsControl keys "up" and "down". Press the arrow until the correct number appears. Confirm your choice with the m button. Dial the remaining digits. Remember: m it is necessary to press after each correctly displayed number. To confirm all the code, hold m for a few seconds. The radio tape recorder will turn on.

6

The display on the screen "1 - - - -" is characteristicfor radio tape recorder with indirect code input. Ie, to get, for example, the first digit, use button 1, pressing it several times. Use 2 - 3 - 4 to enter the remaining numbers. After receiving the correct code, click "loud expert".

7

The inscription "safe" will be replaced after a few secondson ".. .. .. ..". The code is also entered by alternately pressing 1 - 2 - 3 - 4. To confirm the selection, hold fm. The display will again show "safe", and after 3 seconds the radio will work.