Tip 1: How to put a filter
Tip 1: How to put a filter
Any engine system, in particular fuel and oil, should always be in perfect order. Not the last role in this play filter, which retain mechanical impurities and notgive them to get into the engine of the car. Therefore, it is necessary to regularly change the fuel and oil filter. This operation does not take much time, but saves money for repairs.
You will need
- - the key is 6;
- - Figured screwdriver;
- - capacity for fuel;
- - the puller of the oil filter vases.
Instructions
1
Place the car on a level platform andlock the wheels. Open the hood. Prepare a 2-2.5 liters capacity to collect fuel. It is best to use metal, but if not, a plastic bottle will do.
2
Take a key on 6 or a figure-of-thumb screwdriver, unscrew the screws of the clamps of fastening, which fixes the fuel filter to the hoses. Take it off them. Drain neatly the remainder of the fuel from the hoses and filter in the substituted capacity. Keep in mind that the gasoline hose is located below the level in the gas tank. Therefore, douse it with a 8 bolt.
3
Install a new fuel filter on the carso that the arrow on its body, which shows the direction of the flow of fuel, was turned towards the fuel pump. Secure the hose clamps. Otherwise, the fuel filter will create resistance, which will lead to a decrease in the supply of gasoline. Also, the filter element may be damaged.
4
Remove the container with gasoline carefully. Fuel the fuel by manually swapping the fuel pump until the filter is full. Check for leaks in the connection between the body and the fuel cap. filter, as well as hoses. Pull them up if necessary. Start the engine and check again for leaking fuel.
5
Remove the used oil filter from the vehicle by hand or puller. Fill in one third of the volume of the inside of the new filter clean engine oil. Install the O-ring by lubricating it with clean engine oil. Tighten the filter in place by hand, without using the tool.
6
Start the engine. Warm it for several minutes. The oil pressure control lamp should go off after 2-3 seconds after start-up. Examine the connection point filter to the engine during operation. There must be no subterm flow. Stop the engine. Check the oil level with the dipstick, top up if necessary, then tighten the filter.
Tip 2: How to put a zero-resistance filter
Air filter has a strong influence on the work of the car. By cleaning the air and protecting the engine from dirt, it lowers the power of the machine. In this case it is very convenient to establish filter zero resistance, which will help effectively protect the engine from dust and does not interfere with the correct course of the car.
Instructions
1
Choose the right one for your car filter. The devices of different designs for injector and carburetor vehicles are produced. There are also differences in materials filters. There are cotton, mesh and foam rubber filters. Foam finishes are best protected against pollution, but create additional air resistance, which makes them similar to conventional air filters.
2
Disconnect the case of the old air filterAnd, which you used on your car. Usually filterThey are fastened with 4 bolts, which can easily be unscrewed with a Phillips screwdriver. Remove the mounting, remove the housing. Loosen the clamp of the air intake pipe from the air base filtera. Remove the wiring harness from the air flow regulator.
3
Remove the air flow unit from the air casing filtera. Now take off the old filter and remove the case to install a new one. From the air inlet side filterand remove the spring ring.
4
Install in housing filter zero resistance. Attach to filterat a branch pipe of a mass air flow and tighten the connection point with a yoke from the side of the installed device. Now insert the body into the suction inlet and tighten the clamp tightly. Surround filter zero resistance an additional bracket to keep it tightly in place. If filter will move during the operation of the car, you risk damaging the brake pipes. The body itself must be fixed with a metal plate to the place of attachment of the standard air filtera.
5
Attach to filtera cold start hose that will help to avoidoverheating from the engine. The second end of the hose needs to be held under the bumper to suck in cold air from the street. Such a hose is not required for installation filterand air resistance. However, its availability improves the work filtera.
Tip 3: How to put an IP filter
IP-filters are used in private peer-to-peer networks andtorrent tracker to protect against external connections. With the help of the filter program, IP addresses that do not belong to a given network or a certain allowable range are eliminated. This allows you to limit as much as possible external traffic, which is unprofitable for users with limited Internet tariff plans or a limited data package.
You will need
- Installed torrent client
Instructions
1
Download the IP filter file from your websiteInternet provider. If you can not find it, then contact the technical support company or try to download the address list from a third-party Internet resource.
2
Unzip the downloaded archive and move the resulting file (ipfilter.dat) to the folder with your torrent client (for example, C: / Program Files / uTorrent /).
3
Go to the settings through the "Options" - "Settings" - "Advanced". Go to the "Advanced" item and change the value of ipfilter.enable to true. Apply the changes made.
4
If you use uTorrent, click on the top menu item "Feasts" and select Reload Ipfilter.
5
Close the client using the "File" - "Exit" menu, and then run the program again.
6
If in addition to your local peer-to-peer network, youuse another tracker, then install one more client program. To connect to local servers, use the version of the application with the filter, and to download files from external sources - without it.
7
If the provider does not provide a filter, then itscan do by yourself. Create the file ipfilter.dat, open it using standard Notepad in Windows. Enter into it the range of addresses that you do not allow the connection as peers. Then, in the same way, move the file to the folder with the torrent client.
8
If it is not possible to obtain prohibitedIP-addresses, use the program IPFilterGen to automatically create a list. The application can be downloaded from the Internet. Run the utility and select your provider from the drop-down menu. Press Generate. To immediately save the file to a folder with uTorrent, use Save ipfilter.dat to default location. If you are using another client, select the desired directory for saving by clicking Save ipfilter.dat to.
