LovesTheTeam.com

You will need

• - ammonia
• - vinegar

Instructions

1

If contamination has occurred, we advise youFollow the instructions below for cleaning nubuck products. There are several ways to clean the nubuck at home: take 10% ammonia, dilute it with four times the amount of clean water and clean the product with a cotton swab, replacing it as it gets dirty.

2

Wipe the product with cotton-wool soaked in clean wateror with the addition of a small amount of vinegar (a teaspoon per liter of water). It is recommended to hold the nubuck products above the steam and then clean them with special nubuck brushes.

3

Cleaning of nubuck products with the help of special means: shampoos, pen cleaners, special brushes (for example, producers "TARRAGO", "Sitil", "Bar", "Saphir").

4

First clean the dirt with a special triple brushFor the nubuck. Further it is necessary to use foam - cleaner of the above manufacturers. These products will clean the product from various types of pollution, without causing harm, the texture of the material. Do not apply foam to the surface of the product itself. The product should be applied to a sponge or a soft cloth, and then gently clean the contaminated surface.

5

Then again use a triple brush fornubuck. Further, to mask minor defects and abrasions on the surface of the products, to refresh the color and make the product "novelty", it is necessary to use daily creams, special care and protective paints or paints intended for nubuck products. For example, manufacturers "Salamander", "TARRAGO", "Sitil", "Bar", "Saphir", "SALTON".

6

Shoes from nubuck should be cleaned only in dryform. For shoes from such skin, special brushes are used from different companies. Use a special brush to wipe the shoes. Shoes will not only be clean, but also rough. Do this all in a warm, dry place.

7

So that later the dirt on the nubuck was erasedquite easily, you need to prepare the surface in advance. If you have nubuck shoes, then it is best to clean it daily. In doing so, try to use special tools for this material. Best of all, if you immediately and while buying shoes from the nubuck get additional care products. Take a cleansing foam, a colorless aerosol that can repel moisture from a nubuck, an aerosol paint that is suitable in color, a nubuck brush and an eraser that can wipe off dirt. Each tool from the whole list has its important role in caring for shoes from the nubuck. In the future, purchase funds of the same brand as in the beginning. It is undesirable to change them, especially for coloring substances.

8

Immediately after buying shoes from the nubuck createprotection by treating the shoes with a spray three times. When applying each layer, let the product dry completely. As a result, a transparent protective layer will appear on the shoes, which will reduce the number of possible spots from salt, sand and dirt. In addition, shoes treated with a protective spray will be less soaked. After this, the protective spray should be applied again only if you are going to go out into the street during rain or snow. Brushing the same shoes will have every two or three weeks.

9

Before you start cleaning shoes from the nubuck, itsit is necessary to dry well. To do this, some use special tools, electrical appliances or radiators, but this way of drying is strongly discouraged. Shoes from nubuck should dry at room temperature. Do not forget to insert special mold holders into the weather-resistant shoes. If you do not have those, then you can simply stuff your shoes with plain paper or newspaper. Thus, you even accelerate the drying process because the paper will absorb the excess liquid. The main thing is not to change it in time. As a rule, boots from the nubuck are able to dry completely at room temperature for four hours. And if the shoes were soiled in sunny weather, then they would dry up for only half an hour or an hour.

10

Do not use water to clean the nubuck. It not only does not help, but it can also do much harm. As a result, you not only do not clean the dirt, but also spoil the appearance of the product from the nubuck. This applies to cleaning not only the nubuck on shoes, but also its soles. If the foot of the shoe is dirty, it is better to use a dry brush for cleaning. If you do not get a dry cleaning, and there are no special means at home, you can gently remove the dirt with a dampened sponge. But make sure that the water does not soak up the product. If you use a damp cleaning of nubuck shoes with water, then dry your shoes well. After the nubuck has dried from the water, check again if there are any stains left. If they are available, repeat the cleaning and dry again. If there is no more dirt, you should treat the shoes with a spray aerosol.

11

Use aerosol for staining nubuckis necessary in order to bring shoes into a presentable appearance. Paint is able to completely hide all defects and abrasions on the material as soon as possible. Apply the product strictly according to the instructions, observing the distance from the sprayer to the shoes. If you bring the aerosol too close, the paint can come down with clots. If too far, then the coating will be weak and barely noticeable. Then it definitely can not completely hide the defects. Handle shoes with a spray spray quickly. Absorption occurs almost instantaneously. You do not have to process individual sections. Apply paint on the entire shoe. In the end, simply smooth the shoes on the nap with a special brush, so that the villi are light as needed. Do not immediately go out in this shoe on the street, as the nubuck can instantly get dirty.

You will need

• -ammonia;
• - soap;
• - rags;
• - protective skin cream;
• - body cream;
• - Castor oil;
• - Vaseline;
• - glycern;
• - cow's milk.

Instructions

1

The leather handbag should be regularly cleaned fromDust, even if it is completely new, and there are no spots on it yet. This must be done after each journey through the city. Wet a soft cloth and wring it properly. Wipe bag. Lubricate it with a special protective cream for processing leather products. You can use a normal cosmetic nourishing cream.

2

If a dark bag of smooth skin stronglycontaminated, it must be washed. Make a concentrated soap solution. Soap is better to use high-quality household, and you can grate it on a large grater. Add a few drops of ammonia to the solution.

3

Soak a soft cloth in soapy water. Process the entire surface of the bag. Use another bit of rags with castor oil and wipe the entire product. Castor oil can be replaced with glycerin or even petroleum jelly.

4

Leather for making all kinds of productsused for a long time, so among the ways going after it there are many old. For example, you can clean the stain with the most common bulb. Cut it in half. With the cut to the spot, wipe in a circular motion bag, Starting from the edges of the contamination. This method has one drawback - there remains a smell that can not be pleasant to everyone.

5

With a white leather bag worries a little more,Than with the dark. It gets dirty faster, and any traces are visible on it. Wipe off the dust with a damp cloth, of course, you can. But it is better to moisten the rags not in water, but in unboiled cow's milk. Press the cloth and process bag. Milk not only cleans the garment from dirt, but also refreshes the color.

6

For clear leather products, you canApply and another method. Take the egg and separate the protein. Whisk it with a whisk or a fork and mix it with a little raw cow's milk. Dampen the cloth with a cloth or a tampon and clean the stain.

7

Greasy stains on leather products appearoften enough. To remove such a stain without much hassle, lubricate it with rubber glue and leave it in that form for the night. In the morning, gently remove the glue (it is separated without any additional devices, it can simply be pinched by a fingernail). The area where there was a stain, lubricate with a protective cream.

You will need

• Petrol, brush, talc, rag, turpentine, water, vinegar, glycerin, castor oil, mascara

Instructions

1

Most often leather gloves clean with gasoline. If your gloves Light, then this method is ideal for you. Lower gloves in a container of gasoline for a while, then remove and rub them with a brush. After that, fill the tank with fresh gasoline and lower it there. gloves. Then squeeze and wipe dry with a rag, while sprinkle them with talc. This will lend shine and elasticity to your gloves.

2

If you have gloves from the dark skin, then dip them into gasolineOnce. Do not leave them in gasoline for a long time, after extraction, wipe with a rag, talc in this case sprinkle is not required. Also clean the contaminants of the prints can be cleaned with the following solution. Mix petrol and turpentine in a 2: 1 ratio. Apply on gloves, brush them with a brush, then carefully dry.

3

Rinse your gloves In water with vinegar. For 1 liter of water, add 3 tablespoons of vinegar. Also, to maintain the excellent appearance of gloves will help glycerin. From time to time, lubricate them gloves. If the skin of your gloves has become rough andhard, then rub them with castor oil. In a few hours you will see the result. If there are white spots on dark gloves, then smear them with mascara to hide.

You will need

• Liquid soap, baking soda, egg white, milk, washing liquid, ammonia, cosmetic powder, special cleaning cloth.

Instructions

1

Clean the leather strap with soapy water. Pour warm water into the container with the addition of liquid soap and a few drops of ammonia. Wipe a bracelet a cotton disc moistened in solution. Then rinse off the soap with a damp cloth and pat dry with a cotton towel. Then, dry the strap.

2

Mix baking soda with water so that a soft paste is obtained. Apply mass to leather a bracelet and leave for an hour. After this time, gently clean the product with a cotton swab. Wipe the strap with a damp cloth and dry. When the skin dries, rub a few drops of olive oil or glycerin.

3

To clean white leather a bracelet, Stir 1 egg white in a glass of milk. Wet a cotton swab and carefully treat the product. This method will not only clean the skin, but also preserve the original color a braceleta.

4

Wash the cloth a bracelet in warm water with the addition of washing liquiddishes. Take an old toothbrush and rub the areas that are particularly dirty. Then rinse the strap in running water and pat dry with a paper towel. Put a bracelet On a terry towel, folded in several layers, and dry.

5

Mix the toothpaste with a few drops of ammonia and 1 teaspoon of baking soda. Apply the mixture to the silver a bracelet From the clock and leave for 20-30 minutes. Then wipe with a damp microfibre cloth and polish with a soft cloth. Try not to rub the mixture into a bracelet. Baking soda is an abrasive, so it can scratch the metal.

6

Apply a little cosmetic powder to the flannel fabric. Carefully polish gold a bracelet. Then wipe with a clean cloth. Instead of powder, you can use baby powder or crushed chalk.

7

Buy a jewelery salon or workshop special napkin for cleaning jewelry. Thoroughly clean the metal a bracelet from pollution.

You will need

• Milk
• Vata
• Piece of flannel
• Egg
• Care for lacquer shoes
• Soda
• Shoe cream or oil (castor, vegetable, massage)
• Soap
• Nitrate
• Means for the care of leather furniture

Instructions

1

Clean the dirty spots on the white cotton poucha tampon soaked in warm cow's milk. As the contamination of cotton wool change. There is an even more reliable way to give the bag the original beauty. Whisk egg white with a fork and dilute it in a glass of milk. Wipe this mixture with a bag, periodically wetting a flannel cloth. Lacquer coating after cleaning can be wiped with a special tool for the care of varnish shoes. If in the milk to add 5 grams of soda, this mixture will remove the gloss from the sections of the bag.

2

Rub the bag with a transparent shoe cream orOil (baby massage, castor or sunflower). After that, wipe the dirt with a dry cloth. Do not cover the stains on the bag with white cream or toothpaste - it will look sloppy, and problems with cleaning the product will not solve.

3

Try to clean the purse with warm water and soap. In the water, add a little ammonia, and soap choose a baby, removing stains or special for the care of leather shoes. Then wipe it clean with a swab soaked in glycerin or oil. When cleaning, take careful, gentle movements, do not rub the delicate skin too hard. Try not to get wet through the bag! Dry it at room temperature in a place remote from the heaters.

4

Use to clean stains on lightsurface bags are a tool to care for white leather furniture. Consult the seller of the furniture salon. First try the acquired liquid or spray in an inconspicuous place, and then follow the instructions. If you regularly handle such a tool with a leather accessory, it will be protected from moisture and will be less dirty.

Instructions

1

Clean A jacket at Domestic Conditions you need to take into account the features of the material from which it is sewn. Suede A jacket, so that it immediately after the purchase does not spoil your things, you need to vacuum it thoroughly.

2

Stains from raindrops can be removed with a special brush for suede. It is better to choose one that has several different attachments on one handle.

3

The same brush with nozzles made of rubber bands, graters and coarse sponges, you need to go to places where, first of all, shine and scuffs appear on clothes.

4

To clean the street from dirt and dust leatherclothes, it should be wiped very gently with a wet cloth, so as not to stretch the product. Allow the jacket to dry by hanging it on the hangers off from the heaters, otherwise the skin will lose its luster, elasticity, become hard and brittle.

5

You can remove a stain from a light leather jacket,preparing a mixture of talc and turpentine. Spread the stain, press a piece of glass and put the load on top. When everything is dry, you can wipe the skin with a dry rag.

6

If you brush the leather A jacket soap solution, adding ammonia to it, do not forget to wipe it A jacket Castor oil to restore her softness.

7

The leather jacket will again get shine if you rub it with glycerin.

8

If there are spots on the jacket that are difficultwithdraw, then remember what exactly you could stain the thing. Spot from the ink of the ballpoint pen can be removed with acetic acid and alcohol. Check how the dyed skin behaves when processed in an inconspicuous area. Oil stains easily disappear if treated with a swab dipped in gasoline.

You will need

• - soapy water
• - milk and potato starch
• - baking powder
• - cream for white shoes

Instructions

1

Do not wait until the skin becomes visibly dirty,regularly wipe it with a cloth soaked in soapy water. Important nuance - water should be thoroughly boiled before you use it for wet cleaning. During boiling, the mineral salts will precipitate, otherwise they will clog the tender pores of the skin, and you will not be able to remove them any more.

2

If the product is still dirty, wipe it offMilk mixed with potato starch in a 1: 1 ratio. Apply the mixture with a napkin or a very soft brush on the skin, allow to dry, shake off the remains of the starch.

3

On steady spots you can tryto work with baking powder. Pour it a thin layer on the soiled area, drip a couple drops of water on top, a chemical reaction will begin. Under its influence, the stain also dissolves.

4

White leather shoes are very comfortable to ruba special cream for her intended. Remove all dirt from the surface of the skin, treat the shoes with a tool. It contains colorants, which retouched unattractive stains. In addition, the cream will repel dirt and water, shoes will last longer and remain clean.