Tip 1: How to connect an electric stove
Tip 1: How to connect an electric stove
In order to properly connectelectric board must comply with safety regulations, standards of technical maintenance of housing stock. If these standards are not observed, the manufacturer may void your warranty. Incorrect connection of the electric stove threatens at best with the closure of the wiring, in the worst case by fire.
You will need
- - instructions to the electric stove;
- - electric stove;
- - copper three-wire wire;
- - Tester;
- - power socket;
- - automatic switchboard;
- - screwdriver;
- - pliers.
Instructions
1
First, read the instruction - tocorrectly choose the installation site and determine how much wire is needed and which section. Next, remove the plate from the packaging material and inspect if there are any damage or any chips. After all, the aesthetic appearance of the plate is also an important element of our life.
2
The old slab must be removed to prepareplace to install a new one. At the beginning, check the housing cover for connection. The lead-in cable to the apartment should be copper, and its cross-section is not less than 6mm², the introductory machine should be 40-50A. The wire to the electric stove must be separate - no other devices can be connected to it !!! There lived in the cable three: zero, earth and phase. Zero and ground need to be connected to different pads, the ground to the body, zero to the isolated shredder from the body. Connect the phase to a 32-40A machine.
3
Next, pay attention to the other endThe wire was a three-pin socket at 25-38A. To plug the electric cooker into the network, buy small white sockets that are installed in the wall. Assemble the plug. Cable for podvodki from the socket to the plate get PVS 3n4 (three-core for four sections). It is best to leave 2 meters of cable to ensure comfortable maintenance of the plate.
4
Now connect the plate with the cable and insert the plugin the socket. Pay attention to the color of the wire: black - this phase, blue - zero, yellow-green - earth. The earth is connected to the body of the shield, and then to the body of the plate. The machine in the shield should be switched off at the same time !!! Now check to see if everything is connected correctly: to do this, take a tester and inspect the plate. The first thing to test is the lack of contact between phase and earth. To do this, on the tester, set the mode to 2Mom - if the infinity sign is displayed, then everything is connected successfully, you can safely use the stove.
Tip 2: How to connect an electric stove
Electric stoves are complex devices,which are equipped with timers and sensors. The working surface of some of them is made of glass-ceramic material, under which are the ten. The most important thing in the independent connection of the electric stove is the branching of the wires to the terminals. Your safety will depend on this.
Instructions
1
Release the cooker from the package and inspect if there is mechanical damage, check the completeness. Next, make sure that the existing wiring is enough for you to connect. The lead-in cable must be copper and its cross-section must be at least 6mm2. The introductory machine must be 40-50A. For additional security measures it is better to install a protective device - RCD, designed for a current of at least 40-50A and a leakage current of 30mA.
2
There must be a separate electric stovewire, the cross section of which is not less than 4mm2. The cable must have three cores - zero, ground and phase. Earth and zero connect on the board to different pads - the ground to the body, and zero to the bus isolated from the chassis. The bus must be connected by a wire with a zero output of the RCD. Connect the phase to a machine with a rating, depending on the input machine. Import plates allow three-phase connection. This is achieved by breaking the chains, i. E. The first phase - the oven, the second - two hot plates, the third - two more hot plates.
3
Install a power outlet with three or five pins and connect it. Rosettes are both internal and external, what you put, determine for yourself.
4
Connect the power plug to the wire. If the plug has three contacts - the wire should be a 3-core section of 4mm, if the plug has five contacts - take a five-wire wire with a cross section of 1.5mm.
5
Connect electric stove to the cable. Be sure to check that the input machine is switched off! Pay attention to the fact that the black or brown wire is the phase (L), the blue is the zero (N), and the yellow-green wire is the ground. It is connected to the shield body, and after the socket to the body of the electric stove.
6
Plug the appliance into the socket, set it to the level, make a trial run. If you have connected everything correctly, you can start cooking. Bon Appetit.
