Tip 1: How to connect a storage water heater
Tip 1: How to connect a storage water heater
Accumulative water heater Is a medium-sized container that serves to heat and subsequently store hot water in houses where there is no hot water supply through the water supply. AT water heater cold water comes in, which is then heated up to the temperature you set, which you can adjust at will by using a special regulator.
Instructions
1
Of course, you can do all the work yourself, if you do not have certain skills, and we will try to make your work more comfortable and quick.
2
Unpacking water heater, carefully examine it for integrity.
3
Install water heater to the place where further exploitation is planned. Install water heater it is necessary in the position that the manufacturer provides (vertical or horizontal).
4
Move to the place of operation of the water heaterelectricity, if before this point it was not put there. At the same time, it is necessary to take into account the size of the cable and the installation of the protective device, so that no electrical overloads occur in the apartment or house during the operation of the apparatus, since water heater feeds quite a large amount of power, more than 5 kW.
5
Bring water to the water heater and ensure the outlet of the finished hot water from the heater. It is important to consider the upper or lower eyeliner provides the device.
6
Test, connected device. After the operation of connecting the storage water heater, it is necessary to drive the water through it, checking the work and making sure that all operations are performed with accuracy.
7
Use the water heater with pleasure. Remember, if your water does not comply with the standard, then a water filter must be installed at the water inlet of the heater.
Tip 2: Gas storage water heater: features
Hot water in the required quantity is one thingof the main requirements in the modern world. If there is a break in the central water supply system or there is no hot water in your room, water heaters come to the rescue.
The main advantages of gas storage
The first thing to note is the power. So, electric models, as a rule, have a capacity of not more than 3 kW, and a gas boiler - 4-6 kW. This means that it takes much less time to warm up the water to the desired temperature. Secondly, it is known that gas costs much less than electricity. And although the gas water heater will cost you more, later you can save considerably.Disadvantages of the equipment
The main problems associated with the installationwater heater. The boiler needs a centralized supply of gas and cold water. Therefore, as a rule, it is installed in the kitchen or at the point closest to it. Due to the fact that the central part of the gas boiler is a combustion chamber, the installation is directly related to the type to which it belongs. So, with the open chamber, the entire combustion process takes place under the influence of natural draft, and this will require the arrangement of the chimney and the mandatory constant airflow. Here, the moment of calculating the connection point plays a very important role, since all the exhaust air must be diverted and the fresh one must be regularly supplied. The problems of the air circulation system can lead to the supply of carbon monoxide to the room, which threatens to poison. Those appliances that use a closed type of combustion chamber carry out air supply in forced mode. A small chimney is installed, and all the exhaust gas leaves the premises through a special hole in the wall. The difference in models is obvious, they also differ and cost, water heater with forced feed costs an order of magnitude more expensive. Modern gas water heaters are equipped with a reliable protection system. If the appliance does not work properly, the gas supply stops immediately. Responsible for this work is the control unit, which, among other things, monitors the set water temperature and trouble-free operation.Choosing a gas water heater: what you should pay attention to
1. The volume of the tank. It is easy enough to determine it: the volume of water must satisfy the needs of the whole family and do not waste resources. Count, based on an approximate rate of 50-80 liters per person. It is important to immediately determine the location for installation, because a large-sized tank is not so easy to fit.2. Pay attention to what the inside of the tank is made of. The most durable is the titanium and stainless coatings, but they are the most expensive. Acquire a model with the necessary degree of heating for you.Tip 3: How to connect a boiler
In the vast majority of urban apartmentsconvenient and inexpensive water heating is used. In cottages and country houses the situation is different. So, if you have a desire to host water heating in your home, this is done very simply. The main difficulty here is buying boiler, which will accumulate, heat and let water through all the pipes and batteries in the house. About connection boiler we will now tell.
Instructions
1
Mount the storage water heater in such a way that there is a water point nearby. It will also require constant maintenance of the temperature in the room not below zero.
2
While connected boiler use a stand that is speciallyis intended for installation on it of a water heater. Provide pre-shut-off valves to isolate the primary and secondary circuits. To avoid a breakdown, rinse the water system thoroughly. Connect the boiler only after all the operations described above.
3
First fix the hinged bar (the so-calledmaterial), selected in accordance with the strength of the walls. Place the device on a stand in a vertical position and connect it, guided by the scheme provided in the operating instructions and connection boiler. There are such cases, that in the instructionthere are some reservations regarding the installation of the device. On it, you need to set the maximum water flow (if there are no reservations in the manual). For safety reasons, plastic or metal pipes should be used as insulators.
4
Next, you need to make sure that the linethe drain of the safety valve was not closed, and the shut-off valves between the safety valve and the water-heating valve in the connecting line were missing. Connect the water supply line to the position indicated by the instruction. Now you can install a check valve. In advance, provide a water drain in the room with the boiler. For a safety block, a funnel-shaped siphon is needed.
5
To start receiving hot water, immediately after opening the cranes, install a circulation loop between the collection points and the recirculation pipe from boiler. It's all.
Tip 4: Flow and storage water heaters.
Now water heaters are in great demand. Install them in the apartments, faced with the lack of hot water, and in suburban homes. There are two main types of electric water heaters - flow and storage.
