Tip 1: How to tie hooks

Hobby

Tip 1: How to tie hooks

To become a real professional fishermanyou need to learn how to properly tie fishing knots. Having tied a knot incorrectly, one can get trapped, as the fish will drag the hook with the bait under the water. To practice tying knots, it is better to use the usual rope. Follow our step-by-step instructions when tying fishing knots. In it we will teach you how to knit the main fishing knots.

Instructions

The first node, which we will learn to tie,is called "Peak end." Start with the rotation of the line 360 degrees. Make sure that the free end of the line is pointed away from the hook. In this case, the hook should lie on the line. Wrap the outer part of the loop around the hook approximately 7-8 times. Pull the tip of the line near the bent hook, the knot is ready.

The next knot is "Shock" for undergrowth.Tie the edge knot on the undergrowth, through the loop of the knot obtained, skip the light line. Tighten the edge unit more tightly. Wrap the light line around the undergrowth 6 times and thread the free end of the line into the first loop of rotation at the edge node. Pull the main line, while holding the underbrush. Pull until the node is closed. The knot must be tightened well, cut off the unnecessary tips of the line.

Now we will learn how to tie the "Double Krailoop ". Make a loop at the end of your line. Then, on the made loop, tie the edge knot. Add one additional turn to the loop and tighten the knot.

The next node is the Closed node "Half Blood". It is suitable for tying hooks with ears. Prove the line through the eye of the hook. Twist the free end and main line together with 3-6 turns. Thread the free end of the line through the first turn. The more the load on the line is needed, the more turns you make. Pull slightly over the line from which you started knitting the knot. Close the knot, for this, thread the free end of the line through the free loop that formed on top of the knot. Tighten the assembly as tightly as possible.

The node "Greenner".Thread the line through the eye of the hook, make the edge knot. Add 3-4 turns to the edge node. Pull both ends to tighten the assembly. We examined the nodes that are most popular among fishermen. After training on a string, go to the knitting of fishing hooks from the line.

Tip 2: How to tie fishing knots

The loss of fish due to inadequate detachmenta hook or an occasional gear hook for a driftwood is perceived by amateur fishing as an inevitable loss. If the fish is broken due to a wrongly tied fishing knot, there is unqualified preparation of the fisherman.

You will need

- fishing hook;
- fishing line;
- scissors.

Instructions

One of the most popular fishing knotsthe so-called "eight" is considered. In comparison with other existing options, it practically does not deform the line, and therefore the use of this method of tying fishing knots is a kind of guarantee that the fishing line will not be damaged in the fishing process.

In order to tie in the "eight", skipthe end of the fishing line through a fishing hook ring, hang it around the forearm and again put it into the ring. As a result of these simple actions you should get a closed loop. Hook the running end around the root and pass it into the hooking loop of the fishing hook. After tightening the running and root assembly, the ends of the line should be on one side of the ring.

No less popular among modern fishermenconquered and fishing node Palomar. It is ideal for tying a spinner and hook to a thin or medium-thick fishing line. In order to properly tie this knot, fold the fishing line in half, insert the resulting loop into the hook ring, tie the ring to it with the usual knot and pass the end of the loop into the hook's forearm. Firmly tighten the knot and cut the protruding tips of the fishing line.

Quite simple in execution is considered and"Bloody" fishing knot. His awesome name is due to the use as a tool to punish the guilty sailors in the time of Columbus. In contact with the bare backs of the unfortunate, the fishing knot left bloody wounds on them.

Tie the fishing knot "bloody" at allnot difficult. To do this, thread the fishing line into the ring of the hook, wind its running end about the main line 4-8 times (the thinner the line, the more speed). Pass the fishing line into the loop formed next to the hook ring and tighten the knot by pulling the short end of the line.

Regardless of the chosen method, the correctthe tying of a fishing knot provides for following certain important rules. So, experienced fishermen advise wetting the fishing knot before tightening it. According to their statement, the fulfillment of this action excludes the weakening of the line in the fishing process.

Fishermen also recommend not to tighten the knotjerks. The fact is that a sudden jerk can lead to an irreversible deformation of the line, and consequently to its weakening. Tighten the fishing knot should be neat, slow, with a uniform load.

Tip 3: How to Start a Knit Network

The use of fishing nets is regulatedstate. So, from the beginning of 2013, they can be purchased in Russia only by special permission. Fans will benefit from the ability to knit mesh cloths on old fishing patterns. At home, you can perform various products - from legal gear (hints, lifts, cages, saks, etc.) to good old bags - "avosek" and original design items.

You will need

- strong thread;
- shuttle;
- template;
- mesh cloth pattern;
- a lace;
- Support (hook, nail).

Instructions

Choose the right thread for knitting the net -uniform thickness, durable and elastic. Depending on your idea, they can be linen, cotton, silk. You can visit the store for fishermen and buy coils of special fishing threads from kapron (such as "Petrokanat" or Osttex).

Draw a mesh pattern. It will consist of crisscrossing threads, which are fastened together by knots. Each cell has a quadrangular shape. The number of components in each row should be selected individually, depending on the size of the product.

Prepare the shuttle - a long and flat needle,which will help correctly place the working thread and tie the knots. The width of the tool is about 3 cm, the length is 20 cm. If you do not find this tool in a fishing shop, it can be cut from a sheet of thin and durable plastic. Shuttle eye draw a marker and cut out the chisel.

Make a template for the cells - plastic ora wooden plate 10-12 cm long. The finished grid loops will be inserted on it as a knitting needle. The length of one turn of the working thread around the template will be equal to the double size of the mesh web.

You can start knitting the network usingaccessory lace. Make a small loop on the tip of the thread, into which the shuttle will pass. Insert the cord into it and tie the ends into the ring (first knot).

The resulting large loop hang on the support(hook, nail) and proceed to successive tightening of knots. These operations you will repeat many times - to the top row of cells of a cloth to tie the bottom, etc.

Throw a thread on the template and skipShuttle in a loop from the cord. Pull the plate to the first node and tighten the next one. Operate in this order: grab the last 2 threads that stretch upward; clamp them on the edge of the template middle and thumbs; Pull the thread from under the big one to the index finger.

You have a loop. Pass the shuttle through it (it will pass over the thread on the index finger); tighten the assembly on the top edge of the plate. On the one hand, the new nodule will be large, on the other hand - the middle finger. Follow this pattern to complete the first row. When 5-6 loops are formed on the plate, discard them from the left edge and continue working.

Tie the desired number of loops, according to the widthfuture product. After that, remove the lace from the support and unfold the mesh cloth. Remove the template and proceed to the next row. Move from left to right. Continue weaving the net until you get the canvas the right length.