Tip 1: How to glue a sheepskin coat
Tip 1: How to glue a sheepskin coat
Sheepskins are an excellent alternative to a fur coat. They are beautiful, versatile and practical. They can safely flaunt both in severe frosts and during the winter thaw. A quality sheepskin coat can serve its owner faith and truth for more than one season. However, in our bustling life there are situations that lead to premature deterioration of the product. It is possible to accidentally catch somewhere Sheepskin coats And break it. But do not be discouraged, because this annoying gaffe is easy to fix at home.
You will need
- -clay "Moment";
- - liquid skin;
- - Scotch tape;
- - toothpicks;
- - scissors;
- - a piece of suede;
- - Shaver.
Instructions
1
If the gap on the sheepskin coat is too large,It is more appropriate to take it to a specialized repair shop. However, often the skin on the sheepskin tears a small corner. With such a defect you can manage on your own.
2
With a toothpick, neatly align eachThe other end of the rupture and fix them with a piece of scotch. So that he does not leave any traces on the sheepskin coat, glue it once on your own hand. So the scotch will not be too sticky.
3
Unscrew Sheepskin coats Inside out and gently trimSheepskin with scissors. Remain the remaining fur with a razor blade with an ordinary blade. Unfortunately, on the underside of your sheepskin coat you will now be wearing a patch. But it's not worth worrying about it, because it will not be visible to others.
4
Take a small piece of suede, in size itShould be slightly more than a rip on a sheepskin coat. Apply glue on it. Do not use superglue, because it instantly freezes when applied. You will not have time to correct the patch, except for this, this adhesive becomes hard after drying. Apply a piece of cloth with glue to the inside of the hole and firmly press. Wait for the glue to seize.
5
Remove adhesive tape from the front side of the hole,Do this with utmost care. For easy application of the adhesive, drip it onto the cardboard. Slightly pull the edge of the hole and with a toothpick, apply a little glue on them. Press the place of the gap. Remains of glue should be immediately removed from the surface of the sheepskin coat. Now you just have to wait until the glue dries thoroughly.
Tip 2: How to glue a fur coat
A good coat is not only expensive, but also durable. You can go through it in more than one winter. It's unpleasant when the favorite winter outfit starts to break. In this case, it is not necessary to contact the atelier - you can manage the task yourself.
You will need
- - Glue "Moment";
- - thread;
- - a needle;
- - Bandage.
Instructions
1
If the fur coat tore on the seam, then nothing terribleNo - fairly neatly, but reliably, sew this place. Another thing is if the pelts began to tear. In this case, they will have to be sealed. Prepare the thread and needle. The latter should be quite thin, since the work must be cautious. Now pull off the edges of the fur coat and sew them. It must be done as carefully as possible so that the gap does not increase. It is also important to ensure that there is no distortion, otherwise it may affect the appearance of the thing.
2
Prepare glue for work. It is best to use the simplest "Moment". It is most suitable for sealing a fur coat. Do not use the "Super Moment" and similar types of adhesives for this, as they are capable of completely ruining the thing by making the coat rough. After that, it will be impossible to restore its former state.
3
Take a normal medical bandage and put itTo the place where you just stitched. Apply material with a margin so that it completely overlaps the superimposed seams. Well miss the bandage "Moment". It is also recommended not to rub the glue lightly so that the skins are soaked together with the bandage. This will allow them to better grasp with each other.
4
Work on gluing the fur coat is over. Now it remains only to wait until the glue is completely dry. If you have conscientiously treated the matter, the result will be satisfied.
Tip 3: How to seal the radiator
One of the unpleasant car breakdowns isRadiator holes, through which the coolant escapes. Often this problem has to be solved by improvised means, especially if there is no SRS nearby. Or damage to the radiator is not so significant. Often, "cold welding" is used for this.
You will need
- - sandpaper;
- - Acetone;
- - epoxy adhesive ("cold welding");
- - a plastic cup;
- - set of wrenches.
Instructions
1
Identify the location of the leak, then proceedDismantling the radiator. To do this, unscrew the fixing bolts that hold it, drain the coolant and disconnect the hoses. After that, the radiator can be pulled out.
2
Prepare the radiator surface. To do this, dry it, and then carefully sand it with sandpaper so as to leave grooves and roughness for better glue penetration and its interaction with the surface.
3
Treat the surface with acetone to degrease it. It is important to carry out the treatment as best as possible, since the quality of the bonding is closely related to the degree of degreasing of the surface.
4
Prepare the adhesive mixture. To do this, measure out the required amount of "welding", dissolve it in a plastic cup and mix thoroughly. As a result, a homogeneous mixture should be obtained, which during heating can be slightly heated. It is better to prepare the glue in small portions so that it does not have time to harden before applying to the radiator surface.
5
Apply the adhesive to the surface of the radiator. Wait for a while until the patch "cools". The patch can be patched and painted over.
6
Install the radiator in its place, connect all the hoses to it, tighten the fixing screws.
7
Fill the radiator with coolant and check the quality of the patch.
8
Even correctly applied with the help of "coldWelding "patch on the radiator is not durable and may soon fall off. Therefore, it is better to brew a radiator immediately after installing a patch or to purchase a new one. Remember that the components of "cold welding" can adversely affect the skin. Work with gloves.
Tip 4: How to seal a pool
Small inflatable pools in the lastTime is very popular among the population. They are very convenient: they are easily installed, easily transported, do not require large financial investments. But often damaged when installed on an unprepared surface, especially when they are placed in the yard or on the plot. In addition, sometimes they suffer from domestic animals (cats, for example, like to sharpen claws and at the same time they can pierce such a pool). You can seal a damaged area in several ways.
You will need
- Wide and shallow water tank, marker,Cold vulcanization kit, reinforced scotch, scissors, TRS 2002 glue, rubber patch, clamp, fine sandpaper, shaving brush or soft hair brush, laundry soap
Instructions
1
Inflatable pools are made of PVC, rubber,Rubberized fabric. Each material requires its own repair method. But first find the place of the puncture. To do this, lightly inflate the pool. Parts, if not placed completely, immerse it in water. The puncture site is determined by the air bubbles emerging from the puncture hole. Mark the detected marker puncture site.
2
If the pool is bulky and use suchMethod is not possible, use this method: Soak the laundry soap, use a brush or a brush to whip the foam. Apply foam to the surface of a well-pumped pool. The puncture site is determined by bubbles of air blowing under the foam. Mark the damaged place with a marker.
3
If you want to quickly and temporarily glueDamaged area, use scotch tape. Before gluing, gently scrub the damaged area with fine sandpaper. Carefully cut the size of a piece of scotch. Do not touch the sticky surface of the scotch! Put the patch on the damaged area. After such a temporary repair, the pool will last about a week. For major repairs, use special patches from the car kit for cold curing of the chambers. Sandpaper the damaged area. Remove the protective film from the adhesive side of the patch. Firmly press the clamp of the patch against the damaged area. Remove the clamp after 1 hour. Apply a two-component glue of TRS 2002 to the damaged area on the rubberized fabric.
Tip 5: How to glue the battery
To date, to repair the car battery In the service is almost impossible. Car repair shops are not engaged in replacement of lead plates, do not glue the damaged case, etc. Thus, all the old batteryWe are sent for recycling. If you do not want to buy a new part, try gluing the old one.
Instructions
1
In most cases, lead plates come into disrepair, which eventually wear out and wear off. To collect one working battery, Take some good plates and weld them into one body.
2
To do this, clean the upper surface of the housing batteryA, cut a rectangular hole in the center and separate the jumper. After that, rearrange the plates, connect the contact line with a soldering and seal battery. In this situation, the main thing is to achieve complete tightness.
3
Of course, it is better to use thermal welding,Time of which the heated parts of the body are pressed against each other and held in this position for 2-5 minutes. This allows you to repair even large cracks. If at you such situation, use an additional strip which can be cut out from other not working batterya. Before carrying out this operation, drain the electrolyte and dry the device. Pay special attention to the place of adhesion. At the end of the work, subject the fused electrolyte to a double charge-discharge, which normalizes the working capacity of the can.
4
If you do not want to go into suchComplexity, just get a special glue in the special shop that reliably glues plastics and is designed for devices that work with corrosive environments (this category of substances includes electrolyte). In particular, use epoxy glue, also called cold welding. With it, you prevent corroded corps batteryBut with acid.
5
To achieve high quality gluing, clean the cabinet batteryBut from all dirt and dust, apply on itDegreaser, dry and sand with sandpaper. So the glue will hold tight. After gluing, wait a few hours, then pour in the electrolyte and start using battery.
Tip 6: How to seal a refrigerator
It is not always possible to buy in place of the old Refrigerator new. So you have to come up with ways that an old refrigerator can get an attractive look. You can do this by gluing it with a self-adhesive film or painting it with special enamel.
You will need
- - self-adhesive film;
- - silicone sealant;
- - enamel or paint;
- - a pencil;
- - scissors;
- - ruler.
Instructions
1
You can breathe new life into an old refrigerator in many ways. Everything depends on its defects. If in the case Refrigerator There were cracks, call the master from the service center, so he looked and said whether they can be glued, or the refrigerator is no longer subject to repair.
2
Cover small cracks with silicone sealant. Pre-freeze the refrigerator, wipe the walls and dry it thoroughly. Then carefully read the instructions for the silicone sealant and lubricate the area, evenly polishing it over the entire surface. During operation, follow the instructions given on the sealant (there must be written how much it must dry before the unit can be turned on).
3
It is also desirable to find out the cause of theCracks. If the fault is heavily loaded shelves, in the future try not to load them more. Also, the wall can crack due to improper assembly-assembly in production. This happens even in relatively new RefrigeratorX. In this case, contact the store where you bought the refrigerator, and replace it with a better one.
4
The door itself and the outer walls Refrigerator Perfectly refreshes the film - self-adhesive or special enamel. For example, kamaz Refrigerator You can glue a merry film to the color of the kitchen or its individual elements. If you do not want to radically change the appearance Refrigerator, Glue the door and side walls with a white film. The quality film is sufficiently resistant to wear and easily glued to the substrate. To glue the film, measure the dimensions of each part Refrigerator (Doors, side panels), cut off the necessary piece of film, detach it by separating the protective part, and glue it to the refrigerator with a sticky side.
5
Also paint the refrigerator in white withUsing car paints and special enamels. It is advisable to choose the enamel with a spray gun, so you can achieve a more even layer than with a brush. Preliminary surface, which is supposed to paint, you need to thoroughly wash and degrease.
Tip 7: How to simply seal a tubeless tire
At present, in most modernCars are installed tubeless tires. Such tires have a number of advantages over chamber tires: ease of mounting on the rim, relative cheapness (there is no camera), less total weight of the wheel, simple repair in case of a puncture. Often, you can independently seal the tire without being disassembled.
You will need
- Portable compressor for pumping the wheels,Pliers, a knife, a set for repair tubeless tires, a jack, a balloon wrench, special chopping devices for fixing the car when it is lifted by a jack.
Instructions
1
The car must be installed on the parking brake, lock it in place with a chopper, lift it with a jack and remove the wheel.
2
Carefully inspect the wheel for detectionPlace of puncture. More often the puncture gives itself out sticking out of the tread a foreign object (the head of a nail or a self-tap, a piece of glass), which must be removed using a flat-nose plier.
3
Apply to an awl with a screw tip a fewDrops of glue. After that, sewed into the hole puncture, make 7-10 reciprocating movements of the tool and leave it in the hole.
4
Insert a strip of raw rubber into the awl with a needle hole so that on both sides there are equal parts of the strip and apply a thin layer of glue on it.
5
Remove the awl with the screw tip from the puncture and quickly insert in its place a tool with a strip of raw rubber in such a way that there are tails of 1-1.5 cm long outside the tire.
6
Pull the awl back and take it out of the hole. The doubled rubber strip remains in the hole.
7
Cut the protruding ends of the rubber with a knife, pump the wheel up to the working pressure and install it on the car.
