Tip 1: How to fix a hookah
Tip 1: How to fix a hookah
The birthplace of hookah - India. It was from there that this device for smoking, where water was used as a filter and for the cooling of smoke, spread throughout Asia and further all over the world. Often tourists bring hookah with them from travel, but in baggage this fragile product breaks.
Instructions
1
Before you repair the hookah, consider itattentively. The device is very simple and consists of a flask, a bowl for tobacco and a flexible hose with a mouthpiece. For obvious reasons, the bulb most often breaks. She just beats. Replace the flask if you think it is advisable, because in our country it is impossible to buy it separately, so you will have to buy a new hookah and disassemble it.
2
If the hookah does not have external breakdowns, and you smokeYou can not, most likely, deal in the exhaust valve, which is located at the top of the device. Take a thin needle and gently pry her in the tube ball. Moving, he will start to smoke again in the right volume. But if, on the contrary, the smoke is too intense, you will have to remove the hose and replace the ball with a larger one. However, be careful - in cheap models this part of the hookah is non-separable, and therefore you will need to provide options for welding the structure after replacement.
3
If the hookah is smoked, but the smoke is tasteless orunusual, you probably just mis-packed the tobacco. Preparing tobacco for smoking, discard large, hard fragments, and dense clots rub with fingers and lay the prepared mass, not ramming, in a cup. All this will allow you to light a hookah effortlessly. Do not stack tobacco with a slide, since a tightly fitting foil will promote the burning of tobacco and the appearance of an unpleasant aftertaste.
4
By the way, about foil. Preference is given more dense, as it more efficiently distributes coal heat. In addition, it can make more holes for smoking without risk of breaking it. Do not do too large holes, as this can lead to the ignition of coal, from which the smoke will become much more severe. If this still happens, briefly remove the coal from the cup.
5
It is better to use natural charcoal for hookahin kilogram packaging or pressed into plates. If you prefer to smoke with a "pair of traction", how should you "crack" coal on a gas or electric stove. Wait until it turns red from heat about 90%. Then it will be easy to smoke a hookah.
6
Liquid in a hookah poured according to the habit- water, wine and even milk. Wine diluted with water 1: 2. Do not forget about taking care of the hookah. After the end of the smoking session, drain the water from the flask and clean it regularly with special brushes for cleaning the shaft or for the flask, which will make it possible to clean the hookah from the plaque.
Tip 2: How to make a hookah on milk
Stagnant smoking gradually become more popularoccupation and means of relaxation. But in order to obtain the desired effect and pleasure, it is necessary to correctly carry out the preparation process (choice of ingredients and sequence of actions).
You will need
- tobacco, coal, the basis of hookah, milk
Instructions
1
Blockage of tobacco or tobacco leaves affectsthe subsequent draft of smoke, so it's best to casually sketch out a prepared cup. Perforation of tobacco is made by a thin long needle so that small holes are formed on the foil through which the aroma of the tobacco mixture will flow.
2
Further the hookah flask is filledmilk (or at the discretion of people). Some prefer to smoke hookah based on water, wine, cognac, etc. Milk, as a rule, softens the tobacco taste and gives a pleasant aroma of the tobacco mixture. Milk filler eliminates the feeling of bitterness when inhaled tobacco smoke.
3
The last stage is the kindling of coal andsmoking a hookah. For smoking a hookah it is necessary to have strong enough lungs, since the smoking can take from five minutes of constant inhalation of air through the tube. Indicator to the finished hookah is the presence of smoke and a bright red center of coal. The process of smoking continues until the coal is extinguished and the smoke exits the tube.
Tip 3: How to fix an electric stove
The breakage of the electric stove can be caused byimproper operation, and factory marriage. Therefore, before you repair it yourself, you should contact the service center. Especially if the electric stove is under warranty. And yet ... not everyone has the opportunity to consult with professionals.
You will need
- - screwdriver;
- - knife;
- - phase indicator;
- - spare parts (burners, wires, electric plug).
Instructions
1
Inspect the electrical cord and plug carefully, without forgetting to disconnect electric stove from the network. If the plug is disassembled, check the internal contacts by unscrewing the central screw. The cause of breakage can be in the breakage of the cord itself. In this case, simply change the electrical wire to the same one, without forgetting to insulate the open areas and connections. Or maybe there is no voltage in the socket? To check this, make sure, with the help of the phase indicator, that there is voltage in the outlet.
2
The most common cause of a malfunction lies in themost hob. Unscrew the fixing bolts, and then carefully remove it by lifting it at the front edge. Using a vacuum cleaner, clean the interior of the electric stove from dust. Carefully look, whether there are any ragged or scorched wires that are useless connectors. If any, replace them with new ones. Pay special attention to contacts that lead directly to the burners.
3
After you have finished cleaning, connectelectric stove to the mains. Using the phase indicator, check if there is voltage on the controllers of the burners. If it is not, then the cause of the failure lies, most likely, in a power cord or plug. In this case, start the repair from the first step.
4
After making sure that the controllers have voltage,turn on alternately each burner mode. Check to see if the controllers are under voltage in this situation. If not, the spirals of the burner probably went out of order. In this case, only replacement of non-working elements will help you.
5
To install a new burner, remove the old one,untwisting the central nut. Remove the unsuitable hob from the housing, carefully disconnect the wires. Then attach them to the new one. After making sure that all contacts are reliable, assemble the slab.
Tip 4: How to wash a hookah
To the taste of the hookah remained bright and pleasant,it must be washed regularly. If this is not done, very soon there will be an unpleasant smell and bitterness. However, it's not enough just to rinse the water pipe with water, you need to learn how to clean it properly.
You will need
- - Ersch for the mine;
- - Ersch for the bulb;
- - Soda.
Instructions
1
Disassemble the hookah for the main components: a bowl, a flask, a tube and a shaft. This list can also include additional accessories like a saucer for ash.
2
The first step is to clean the bowl. First rinse it thoroughly with water. Then put soda and hands wipe all available places, both from the outside and from the inside. You must get rid of all the tobacco that has stuck to the bowl.
3
Pass the water through the hookah's shaft. Then put soda on the ruff and thoroughly wipe it. After you pour the soda into the shaft and start cleaning it with a ruff. Look inside. There should not be any extra fine particles inside.
4
Rinse the tube. To do this, type water there and turn it intensively. Release one end into the sink and allow the water to drain off with dirt, then blow out the leftovers. Repeat the procedure until the water becomes clear.
5
Pour the soda flask inside and pour a little water. Then go brush on the walls, removing all dirt. Repeat until the unpleasant odor disappears.
Tip 5: How to build a hookah
Smoking hookah Today it's fashionable. It is offered in cafes and bars, clubs. But you can do this entertainment at home, if you, for example, brought hookah from a trip abroad to the southern seas or bought it at home. To not spoil the pleasure of the process, you need to be able to smoke hookah correctly.
Instructions
1
Collect hookah and make sure that all its parts are adjacent to each other tightly. Remove the cup and very tightly tuck the upper hole with your hand. Then try to suck in the air. If it did not work out, everything is in order - hookah is sealed.
2
Put the pre-prepared tobacco in a cup -so that to its edges there should be not less than 5 mm. This will protect tobacco from ignition from coal. To stack it is necessary not so densely, leaves should be developed, it is possible some times to pierce their spokes through the bottom aperture of a cup that ventilation was better.
3
Place a special mesh or ordinary piece of foil under the charcoal. Cup, too, cover with foil - tightly. Then pierce a few small holes with an awl or toothpick.
4
In the flask pour cold water - so that the tube of the shaft was in the liquid for 3-4 cm. If the water is poured more, it will be difficult to inhale, if less - the filtration will deteriorate.
5
Light the coal with a lighter. If it is natural, it should turn red on all sides; if special, self-igniting, it should get the same color. Then put the coal in the middle of the mesh or foil and cover with a hood from hookaha. When the tobacco is warm enough, move the coal to the edges of the cup. Now you can start smoking hookah.
Tip 6: How to make a homemade hookah
Eastern exotic becomes more and more popular in our region, and now it is difficult to find a restaurant that does not offer money for smoking shisha. Many people buy hookahs for home useuse, but quality imported hookahs are worth a lot, and lovers of eastern flavors have to spend at least a hundred dollars. You can save money and make a hookah from improvised items, as the principle of its design is quite simple.
Instructions
1
Instead of a flask, use a metal teapot or similar container. For smoking, use an ordinary shower hose, or purchase a special hose for shisha in a specialized store.
2
For the mine shisha get a steel tube 30 cm long,a hot plate for the gas stove and a metal strainer that is usually installed in the kitchen sink. You will also need a soldering rod to connect the metal surfaces.
3
Connect the metal tube to the gasburner, making the connection tight. Connect the opposite end of the tube to the cover of the teapot. To do this, remove the handle from the lid and drill a hole to match the diameter of the metal tube.
4
On the tube, make two grooves for the solder, andthen immerse the tube in the kettle to a small height by installing the lid in place, solder to the lid of the edge of the tube. Then open the lid and repeat the same on the reverse side so that the tube and lid connection is strong. Grind the spike file.
5
To the spout of the teapot, attach the hose from thesoul. To do this, cut the tip of the nozzle and install the hose inside. From the outside, tightly tighten the joint with an insulating tape. Top with a metal nut on the tip of the kettle.
6
Places for connecting the kettle with the lidSeal with foil, then install a funnel made of foil for tobacco into the gas burner. On the hotplate, put a metal strainer. Now you can light a hookah and check it for efficiency.
Tip 7: How to smoke a hookah on milk
Hookah has long been not uncommon in ourlife. There are so many kinds of tobacco for hookah and everyone can choose what they want. Hookah can be cooked on water, juice, alcohol and even on milk.
You will need
- - Hookah;
- - Milk.
Instructions
1
Pour the cooled milk into the flask. Milk should cover the end of the shaft by 1.5-2 cm. Milk should not be bold, so you can dilute it with water. One glass of milk is diluted with two glasses of water. The density of milk is greater than the density of water, so the smoke, passing through such a filter, will become softer than usual.
2
Fill a cup of hookah with tobacco, leavingedges about 3 mm, so that when smoking tobacco is not burned. Put tobacco not with one pressed layer, but in small groups. Tobacco with strawberry and coffee taste is suitable for the hookah on milk.
3
Take the foil and fold it into two layers. Firmly cover the cup with foil. With a needle, make small holes in the foil, 3-4 mm apart. If you do not have a special foil for the hookah, use the foil from the chocolate.
4
Collect the hookah. First insert a shaft in the flask, then put a cup of tobacco on the shaft and insert the hose. Use special pincers to take the coal and heat it. Put the hot charcoal on foil and light a hookah. To smoke it was easier, put two coal at once. Light the charcoal above the plate, or directly over the cup of the hookah.
5
After smoking, be sure to clean the hookah. Thoroughly rinse all the parts, otherwise the leftover milk may sour and an unpleasant odor will appear. And if the remaining milk is dried in the hose, it will be very difficult to wash them. Milk can be reused, but not later than 3-5 hours. With repeated use of milk, tobacco should be of the same taste as the first time.
