Tip 1: What kind of gas is in the lighter
Tip 1: What kind of gas is in the lighter
Lighter - one of the most sought-after things inour world. She constantly navidu. Probably, there is no such person who at least once in his life did not have a gas lighter in his hands. However, how its mechanism works, not everyone knows.
Types of gas lighters
Gas lighters are divided by design intoflint and piezo lighters. In flint lighters made of plastic, gas comes when the lever is pressed under the wheel, and in the metal ones - when the lid is opened. Piezo lighters, in turn, are divided into conventional and turbo. In ordinary piezo lighters, the fire is ignited by electric charge. The difference between turbo lighters and conventional ones is that the gas is supplied under pressure - and the fire does not go out from the wind.What gas is in the lighter?
Most often in lighter is liquefied butanehigh purification, a mixture of liquefied butane and propane, which is an order of magnitude cheaper, or isobutane. Pure propane was used only in old-style lighters. He was refused, as this gas is explosive. The boiling point of propane comes at -20 degrees Celsius, which can lead to an explosion. The boiling point of butane is +10. Butane lighters can explode only when exposed to direct sunlight. It should be noted that lighters produced in the CIS are designed for a mixture of propane and butane. They can work even on a mixture of low purity. Imported lighters can only work on butane or isobutane triple purification. In general, these are expensive and popular models of lighters that can simply spoil a substandard gas. Some branded lighters work only on liquefied isobutane. The propane-butane mixture has a higher pressure than pure butane and a lesser degree of purification. Such a mixture is not suitable for piezo lighters. More recently, lighters have been manufactured in cheap disposable versions. Now these types of lighters are very rare. Reusable lighters of silicon or piezoelectric type are mainly produced.Than to fill a lighter?
Refill the lighter is only relevant inIf this is an expensive model. The cost of a gas cartridge is much higher than the cost of an ordinary reusable lighter. To refill the lighter, you need to buy a can of liquefied butane or isobutane triple purification.How to properly fill the lighter?
1. Turn the lighter over with the filling valve. Most models have it from the bottom. Insert the cartridge shaft into the valve, press and hold for 10 seconds. In this case, the can should be placed downward with a rod. If the gas is properly refueled, the gas must not escape. After refueling, you must wait a few seconds. To get rid of excess air, you need to set the combustion level valve to minimum. This valve for most lighters is located next to the refill valve. In this case, the lighter may not catch fire, since the air that has accumulated in it will first escape. Adjust the combustion level. At this stage, a large flame is possible, which will burn out the accumulated dirt. The gas cylinder usually has up to 30 gas stations, but this depends on the volume of the can and the volume of the lighter.Tip 2: How to fill the lighter with gas
If the flame of your favorite gas lighters has ceased to gaily twinkle in the night and you have nothing to light a cigarette - it means that the fuel ran out, that is, gas.
You will need
- Lighter, a can of gas for lighters, a little witty
Instructions
1
If the design of your gas lightersProvides for refueling, then you should look into a specialized store or kiosk, taking a lighter with you. When choosing a can, it is best to pay attention to special cartridges equipped with a cap, under which there should be a set of nozzles, for different types of valves of lighters. Under the cap can be up to 10 nozzles, which guarantees you a high-quality refueling. After inspecting the nozzles and comparing them with the design of the valve lighters, you will understand which one is right for you.
2
So, choosing a suitable attachment, it is necessarybreak off from the bottom of the cap, then put on the valve of the can. Clean the lighter adapter valve from possible contaminants (it's easiest to do this with a clean earwax stick). Then, inserting the nozzle into the adapter valve of the lighter, press firmly on the can. If a gas leak occurs, check that the nozzle and the lighter valve match. If so, replace the nozzle. If it does, try again.
3
How to determine if the lighter is charging? It should become cold, icy, because liquefied gas under pressure reacts with the environment and cools objects. If the lighter is transparent, you can be sure of its fullness visually. If not - then enough to fully charge 20-30 seconds of download.
