Tip 1: How to restore enamel in the bathroom

Apartment and cottage

Tip 1: How to restore enamel in the bathroom

Enamel bath with time darkens, it appearscracks and chips. Yes, and washing with the use of bleach, as well as cleaning with aggressive detergents thinens the enamel, because of what it is covered with stains, where the paint layer is practically absent.

Instructions

Replacement of the bath will be very expensive, becauseIn addition to the cost of the bath itself, you will have to pay for the installation work. There is another option to install an acrylic liner, which is done easily and quickly, but unfortunately this is also quite an expensive way out, and it will not always be possible to purchase them. But you can restore the enamel in bathroom - this does not require special skills andFirst of all, select the enamel for the bath. Enamels in aerosol cans are easier to apply, but they have a much shorter service life than enamels in conventional packaging. In addition, you will need a primer, which can also be purchased in aerosol packaging.

Thoroughly wash the bathroom of all contaminants,traces of rust and fragile and flaking scales of old enamel. If possible, polish the entire surface mechanically. Treat the surfaces covered with rust with an active cleaning agent or with a solution of oxalic acid. Wash off any remaining detergent and thoroughly drain the bath. After that, exclude the possibility of water entering the bathroom - it can completely ruin the future enamel coating.

It is also desirable to reduce the humidity in bathroom room with a reflex heater, or just a few hours ventilating the room.

Apply to the prepared surface a primerin accordance with the recommendations indicated therein. If you use an aerosol primer, always use respiratory protection - a cloth bandage or a respirator.

After solidification of the soil, apply enamel in 3-4 layers with an interval of 15-20 minutes and allow it to freeze for 1-2 days (depending on the type of paint used). Before use bathroom Rinse thoroughly with a cleanser with plenty of water. Recover the enamel in bathroom in a similar way, almost unlimited times.

Tip 2: How to repair the enamel bath

Today, few people repair old plumbing equipment -easier to buy a new one. However, the situation when a new bath accidentally appeared chipped or cracked, is not uncommon. In this case, it makes sense to carry out an uncomplicated repair yourself.

Restoration of the bath today can be carried outin several ways: by installing the liner, treating with acrylic ("liquid", filling bath) or enameling. The latter option is the most popular, due to the simplicity of the procedure and the low cost of consumables. To achieve maximum effect, it is necessary to thoroughly read the instructions on the enamel package and to fulfill the simple requirements described below.

Preparatory work

At the initial stage it will be necessary to clearbath from the old enamel (surface layer). To do this, you can use a waterproof sandpaper and a drill with a Velcro attachment in the form of a circle. Treat the treatment, first sprinkle the bath with a cleaning abrasive powder and moisten it with water. The result is a gruel, which must be carefully removed. Inspect the tub for rust; if any, the place that has been corroded must be cleaned. Deep chips must be repaired with epoxy glue or a mixture of white nitro-enamel with the glue "Supercement". At the final stage of preparation, a smooth, dry, smooth surface should be obtained. The next step is priming. You can choose any composition, preferably in aerosol packaging. Before use, read the instructions in which it should be indicated that this type of primer can be used in metal processing. In the priming process, make sure that there are no bubbles of air and streaks. After the work is done, dry the bath well.

Application of enamel

It is more preferable to purchase enamel in a cantare, tk. Aerosol packaging requires a large amount of solvent, which reduces the life of the enamel coating. To apply the enamel composition you will need a brush, preferably from a natural material, or a tissue swab. The latter option is preferable, because prevents the hairs from entering the enamel layer. Application of the latter is done in several layers with drying of each; more details about the technology should be told on the manufacturer's packaging. Work should be done at a temperature of 20-23C. Enamel will harden after a few hours, but you can talk about complete drying after a week. The restored bath will last longer if you exclude contact of the coating with chemically aggressive substances; bleaching powders, abrasive cleaning agents such as "Pemolux", Comet or acid-containing products.

Tip 3: How to restore the bath

Over time, the enamel of the bath bursts, acquiresyellow shade, from unpleasant water there are unpleasant rusty divorces. A complete bath replacement, of course, can correct this situation, but it requires not only heavy plumbing movements, but also reconnection of communications, replacement of tiled walls and floor. If you are not yet ready for a complete renovation of the bathroom, try simply to restore the old one a bath.

You will need

- an acrylic liner;
- cleaning powder;
- Abrasive stone;
- white spirit or gasoline;
- enamel;
- paint spray gun or brush;
- liquid acrylic.

Instructions

Carry out an external inspection of the bath, if the bodycracked or deformed, on the place of plum chipped - normal restoration of the enamel does not help, more effective measures are needed. For example, try to pick up the finished acrylic liner in the hardware store. If you succeed, set it according to the instructions inside your bath and enjoy the new look of the room.

To fix small cracks and rough spots on the enamel, chipped, brownish tint - try to restore the enamel. If it is not possible to invite a specialist, cover a bath enamel yourself.

Apply a cleaning powder to the surface, notcontaining chlorine, and clean it with an abrasive stone fixed in a drill or bulgarian. The surface must be even and uniform, without shells and notches. Be sure to use gloves and a respirator, as fine dust and debris can fly away quite far.

Large crumbs sweep, vacuum, rinse a bath water. Clean the surface of rust and degrease it, for example, with white spirit or gasoline. Dial the complete a bath hot water, wait for a few minutes and drain the water. Wait for complete drying.

Prepare the enamel by mixing the hardener and the liquidpart in strict accordance with the instruction on the bank. Apply a primer coat of enamel with a spray or brush on the surface of the bath. Of course, if you use a nebulizer, you will get a better result.

Wait for the surface to dry and applyone layer of enamel for alignment. Do not allow dust and debris to enter at the time of painting, otherwise the coating will be damaged. Take care that there are no bubbles and streaks.

Tip 4: How to restore the bathroom

Sometimes getting rid of an old bathtub is much more difficult than restoring it in one of the available ways. This is especially true for cast iron baths - very heavy and often too bulky.

You will need

- special enamel for cast-iron baths;
- Brush;
- primer.

Instructions

Choose the method of restoration of the cast-iron bath. To date, there are three: coating the surface of the bath with enamel, "filler bath" and acrylic liner.

If you decide to use the first oflisted methods, purchase a special enamel. It is covered by hand with a brush. Enamel is also sold in aerosol cans, but in quality it loses the usual.

Rinse the tub thoroughly from all contamination and rust. If necessary, use primers before applying enamel.

Apply enamel from top to bottom, so youavoid possible drips. You can also use a roller, but the consumption of the coloring material will increase somewhat. Do not try to do everything the first time, it is permissible to apply several layers.

Use the method of restoration "loadingbath ", if on cast iron there are deep cracks and chips. Prepare for the fact that there will be a lot of dust: use an old sheet and unwanted newspapers. The essence of the method is this: in the process of filling a special liquid substance - stakryla - all the voids and cavities are instantly filled. The surface of the bath is sanded with special tools. It takes four days to dry - just as much you can not use it. Unlike the previous one, this method gives an impeccable smoothness of the surface and prolongs the service life of the bath for a much longer period of time.

The essence of the third way to restore the bath,called "acrylic liner" or "bath in the bath" is that the liner, made of solid acrylic, is applied to the bath from the inside, and then attached to its sides. To make such a liner, it is necessary to make preliminary measurements of the restored bath. With careful use and careful care of the bathroom, this insert can last 5-6 years.