Tip 1: How to Tint the Glass
Tip 1: How to Tint the Glass
Independently to sink its glassThe car can be used with a tint film. To make toning beautiful and durable, never use low-quality films made in China.
You will need
- - a tint film at the rate of 1 standard roll for 4 side windows;
- - plastic scraper or rubber spatula;
- - stationery knife;
- - detergent, shampoo, warm water, dry rag without lint, spray;
- - building, installation or household hair dryer.
Instructions
1
Car glass tinting togetherWith an assistant in a dry dust-free room or on the street in windless weather. Remove the seals and wash thoroughly with detergent intended for toning the glass. Pay attention to the cleanliness of the windows in the corners. Fill the spray with washing solution (shampoo with warm water).
2
Apply a soap solution on the spray gunouter surface of freshly washed glass. Attach the tint film to it with a dark layer inside, transparent to the outside. Take care not to confuse the sides. Slightly divide the film from one of the corners to make it easier to navigate.
3
After applying the film, align it and cut it offEdges, leaving a stock 1 cm wide. After that, apply a lot of soap solution on the inner surface of the glass. Quickly, so that the solution does not have time to dry, separate the dark layer of the film while wetting it with the solution from the spray gun. To facilitate the process, do the work together: one must securely hold the transparent layer, the other - gently pull and moisten the dark layer.
4
Attach a dark layer to the inner innerSurface of glass. Then spray again with a spray gun. Apply a transparent film layer (to protect it from mechanical damage) and carefully smooth it with a rubber spatula. Using a standard plastic scraper can lead to scratches. Smooth out smooth movements from the center to the edges of the film. Remove air bubbles until the transparent film dries and disappears.
5
Remove the clear film. Cut off the protruding edges of the tint film, gently carrying a sharp knife-edge knife along the edge of the panes. Do not use the standard knife from the kit to the purchased film. He quickly becomes stupid and begins to tear the material. At the end, dry the glass around the perimeter with a hair dryer. After waiting two days, insert the seals in the door. Until then, avoid opening tinted windows.
Tip 2: How to better tint the machine
Despite the tightening of fines for tintedCar glass, the popularity of toning remains the same. After all, the smoked windows of the car not only give it a stylish appearance, but also solve many practical questions - hide passengers from the scorching sun, and things in the cabin from other people's views. In order to make the toning of the glasses qualitatively, it is important to observe several conditions.
You will need
- - professional tool for toning;
- - stand for unfolding the film;
- - household air humidifier.
Instructions
1
Tint the car glass only in a dry andclean room. Never make a tint in the street, otherwise under the film you will have all the speckles because of the particles of dust and dirt that came under it. If you are tinting in a garage, make a wet cleaning in it and get rid of unnecessary trash. Turn on the humidifier or air purifier to prevent dust from flying through the garage. On the floor bed linoleum (you can old, but clean), so that the water from the processing of glasses flowed onto it and it was easier to wipe it.
2
Make a special stand for cuttingTint film. It can be made of metal pipes of small diameter. Weld to the two pipes on top of the two crossbars (height of the stand do according to your height). On the crossbar, pull a sheet of linoleum or polycarbonate. On this improvised stand you will unfold and cut the film.
3
Get professional tools forToning. For accurate work, household knives and scrapers are strictly not suitable. A professional tool can be found on specialized sites. You will definitely need a scraper for water, a forcing, blades, an automatic sprayer, a film-forming dryer (can be replaced with a powerful building hair dryer). Since such a tool is very expensive, you can buy a special set for toning: the tool will be slightly worse in quality, but cheaper.
4
Choose a tint film. Do not skimp on the film. Cheap Chinese material will start to buoy after a couple of months, and winter can not survive. Films of American manufacturers are considered to be the most durable and strong. Even the usual black tint combines a lot of functions: protection from fading, optical transparency, protection from sunlight. You just have to choose the color of the film, the bandwidth of light and the intended purpose. After all, the films are not just black, but, for example, colorless, which are glued to the tint or glass and protect passengers from ultraviolet radiation. Or impact-resistant films that do not allow the glass to crash and crumble when it strikes.
Tip 3: How to tint the machine yourself
Recently, drivers are increasingly decidingto brighten up your car. First, the tint film protects you and the valuable contents of the salon from prying eyes. It also protects the glass from cracks when small pebbles come in, and passengers - from glass shards in the event of an accident. Secondly, it significantly reduces the strain on your eyes during the day. And thirdly, toning simply beautifies the appearance of the car. Tint the car in the workshop is expensive, so you can try to do it yourself.
Instructions
1
The first thing you need is to buy the right oneyou tint film. On sale you can find films for any "taste and color", but be careful - not all of them correspond to Russian GOSTs for light transmission. Now you need to remove and rinse all the glass. Wash the glasses carefully, since any specks of dust on the glass will necessarily be a blister under the film. After that, they should be wiped with a dry cloth, leaving no thread or lint.
2
Now that the glasses are clean and dry, dilutewater-soap solution - about 4 drops of shampoo or detergent per liter of water. Gently bend the corner of the film from the bottom corner. Peel off the film from the clear layer and immediately spray it with the solution from the spray gun. Then evenly spray the glass and apply a prepared film on it. With a spatula, expel water and air from under the film with movements from the center to the edges.
3
When there is not a single bubble left under the film,Take the blade and cut the protruding edges of the film. After that, dry the glass with a hair dryer (preferably a building brush). If there is no hair dryer, then leave this glass to dry, and go on to the next one. Attention! After the label is not recommended for a week to lower the glass and wipe them with detergents. Also, after tinting the glasses, avoidance of detergents based on abrasive powders should be avoided.
Tip 4: How to tint car glass?
A procedure like sticking a tint film on the glass of a car can be performed by the motorist himself. We only need time, material, tools and, importantly, accuracy.
You will need
- - an ionizing film;
- -Plastic sticker to smooth the film (if it is not included, then something replacing it);
- -Shampoo or liquid soap;
- -hand sprayer;
- -knife;
- - a means for washing the glass;
- - napkins;
- -water.
Instructions
1
First you need to cut a piece of tintedfilms in the form of glass. For this, we spray the glass with water and apply a film on it, so that the protective film of toning fits slightly to the glass. At the edges of the film you need to leave a reserve of about 7-10 mm. If the glass is lowering, then leave a little more.
2
After the workpiece is made, we remove the film, andproperly my glass on the inside. Dissolve a little shampoo in water and pour into a spray. Now spray all the glass, take a tint, and in some upper corner remove a little protective film. In the place of separation you need to apply a little shampoo solution.
3
After gluing this angle, we begin to remove the protectiveFilm, gently pulling it out from under the tint, but at the same time you also need to press the tint film to the glass. Do not rush - once it is not stuck, because the glue is neutralized by shampoo. The neutralization time is about 10-20 minutes.
4
Now the protective film is removed, and the tint film is slightly caught on the glass. We adjust it and glue it. Take the sticker or its substitute, and gently squeeze the shampoo and air from under the film.
5
For extra film around the edges, cut it so that it does notReached the edge of the glass about a millimeter or two. Part of the film adjacent to the lower seal, a little bit under this same seal. So, the tint film is pasted, and will dry for about a day. At this time, try not to lower the glass and do not turn on their heating.
