Tip 1: How to remove the trunk
Tip 1: How to remove the trunk
The trunk is a place in the car intended for storage of things of the driver and passengers. Most often, the luggage is collapsible, and if necessary they can be removed on their own.
Instructions
1
There are both collapsible and non-separabletrunks. An unassembled is usually the rear trunk of the car, which is located at the rear of the car and is part of the bodywork. In this case, you can remove the trunk lid by yourself. To do this, remove the bullets along the perimeter of the skin, then remove the inner lining of the boot. Then, using a screwdriver and a suitable screwdriver, remove the screws securing the hinges of the trunk. Now you can remove its cover.
2
If the loops and screws are not easily released,grease them with oil, and try to remove after a while. If necessary, remove the entire rear part of the body, including the boot lid, for example, after an accident, here you can not do without the help of specialists at the service station.
3
Demountable are usually hingedLuggage, which are located on the roof or the rear door of the body. The way they are disassembled will depend on the model of the trunk itself, as well as the anchorages that hold it. The easiest to disassemble - the trunks, with clamping and snap fasteners, and hinged models. To remove them, simply unfasten the fasteners and remove the supports or crossbeams. Fold all the attachments and the trunk itself in an accessible place to store for the next installation. If space allows, place all the parts in the standard rear carrier of the car.
4
More difficult to disassemble are hingedModels, fixed with self-tapping screws. This trunk is screwed into the body of the car, and after its removal on the body there are holes, as well as abrasions. Read the instructions of the car or choose a suitable screwdriver and, with the screws lubricated with engine oil, carefully unscrew them, trying not to damage the body paint. Remove the trunk. Carefully zashpatlyuyte places from the screws and paint the body in the appropriate color shades, using a balloon with paint.
Tip 2: How to secure the trunk
Quite often, car owners experienceDifficulties due to lack of space in the trunk. The most convenient option in this case is the installation of an additional trunk on the roof of the car, which not only allows you to take more things on the road, but also improves the appearance of the vehicle. The car will get a complete look and great functionality.
You will need
- - L-shaped key;
- - plastic key;
- - Hexahedrons.
Instructions
1
Before proceeding with the installation of the trunkRoof of the car, clean it of dust and dirt. Finding a railing for a long time on the roof can cause the color of the paintwork under the construction to be different from the base color, that is, the car will burn out in the sun. Such a defect is easy to remove by polishing.
2
When installing the trunk on the car, insertPlastic key into the available special hole on the roof. After this, rotate it clockwise 90 degrees until you hear a characteristic click.
3
Then remove the support cover and install into the slotarc fastening elements. Secure the support in the arc using the cam. To do this, press it upwards first to the arc. After completing the assembly of the arc, attach it for fitting to the roof of the car. Before you try on the trunk, adjust the cam position so that the support on the arc is equal in width to the width of the roof of the car.
4
Place on the arcs of the support so thatTheir cushions were located to the center of the vehicle 1-1.5 cm closer than the intended place of installation of the trunk. Then tighten the fixtures with the L-shaped key. They must be securely fixed. Then cut the rubber gasket, check if it matches the dimensions, and insert it into the slot of the luggage compartment arch.
5
Snap on the installed arcPlastic cap. Also close the lid of the support, for this, insert the plastic key into the lid socket and turn it counterclockwise 90 degrees to a characteristic click.
6
To install or remove the pressure on the support,unscrew the existing mounting bolt. During this process it is important to hold a cylindrical mortgage with your hand, since it often jumps when the bolt is unscrewed. After that, insert the clamp and tighten the bolt. Stick a sticker on the back of the support.
