Tip 1: How to disassemble the trunk
Tip 1: How to disassemble the trunk
Additional trunk, which you have installed to transport the necessary goods, should be periodically removed. If you do not do this, then coloring the car under trunkit will be darker, especially if you often leave it under the sun. Recommended frequency of removal trunkbut - every time, as soon as the need for it has disappeared. This does not mean that you need to shoot it once a season, namely immediately after the necessary loads are transported.
Instructions
1
Disassemble trunk follows in the exact sequence from its installation, only in the reverse order.
2
The disassembly method depends on the model of the installed trunkbut also the fastenings on which it is installed.
3
The easiest option for dismantling is considered trunkand with clamping and snap fasteners, as well as hinged models. To disassemble them, it is sufficient to unfasten the fasteners and remove the crossbeams or supports. All fasteners and trunk You need to add it to the available location for the next installation. Most often mounted trunk stored in a standard trunke car, so that if necessary, he was always at hand.
4
If you leave with trunkonly on a summer residence or on the nature, and in all other cases to you there is no standard trunka, then the hinged can be put in the garage on the shelf.
5
The most difficult disassembly trunkbut is a model fixed with self-tapping screws. This option is better to shoot at the end of the season, when you need an extra trunk. And this is despite the fact that the paint on the car will look uneven.
6
After the end of the summer or holiday season, the self-tapping screws, trunk remove. All the places from the self-tapping screws should be filled and painted with the appropriate shade of paint from the can.
7
If the mounts trunkbut do not lend themselves to squeezing or unbuttoning, then oil them and try to take them off after a while.
Tip 2: How to disassemble the trunk lid
The trunk of the car is capacious and very convenientto transport things. However, in some cases, its locking device fails, so it must be dismantled for repair or replacement. Dismantle Castle Trunk you can do it yourself, without the help of qualified specialists.
You will need
- - the key to the trunk;
- - screwdriver;
- - spindle and face spanners;
- - pliers;
- - Insulating tape.
Instructions
1
Open the hood of the car and disconnect the battery. It is necessary to do this to ensure safety, otherwise there is the possibility of electric shock when dismounting the lock Trunk.
2
Open the trunk of the car and unscrew the elements securing the upholstery. Detach the fasteners together with the upholstery and set aside.
3
Remove the lamp holder thatis used to illuminate the license plate. Remove the lamp from the cartridge first. Using a screwdriver, press the catch holding the shoe with the wires on it. Disconnect the connector from the luggage compartment lid lockout.
4
Insert a screwdriver into the slot of the bracket and pull out the cable of the lock cover drive. Turn the tip of the cable in the slots and disconnect the cable from the lock.
5
Pull the cable out of the hooks and pull it out of the lid amplifier. Pincers clamp the tips of the holder.
6
Remove the holder from the socket, and then pull the wiring harness through the hole. Loosen the fixing screws securing Castle to the lid Trunk. Disconnect Castle.
7
To remove the latch of the lock, remove the trim of the rear wall of the luggage compartment and unscrew the bolts securing the latch. Remove the latch of the locking device.
8
Inspect the parts of the lock and the latch. Fix the fault by replacing the deformed parts. Before installing a new lock, remove dirt from the surfaces on which the device will be attached.
9
Carry out a repaired or new installationlock in the reverse order. Make sure that all connectors are in place without distortion and gaps. Pay special attention to the installation of the cable. When installing, use a flat screwdriver, having pre-wrapped its tip with several layers of insulation tape to protect the lock parts from deformation.
