LovesTheTeam.com

You will need

• - DVI-HDMI cable.

Instructions

1

First, find the appropriate pair of connectors, throughwhich you will be connecting. Naturally, to ensure the best picture quality, it is recommended to use digital channels. Video cards of computers are endowed with HDMI and DVI ports, which transmit a digital signal. Despite the fact that the DVI port is found in modern plasma and LCD TVs is rare, it can be replaced with an HDMI port using a special adapter.

2

Obtain a suitable video cable and adapter,if it is needed. Connect the video card of the computer to the TV. If you use both the monitor and the TV, the first device can not be turned off. Now turn on both equipments. Wait for the PC operating system to boot.

3

Open the TV settings menu. Find the item that shows the connectors for connecting video cables. Assign the source through which you have connected to the computer.

4

Now configure the computer. Open the control panel and go to the "Appearance and Personalization" menu. Select "Connect to an external display" located in the "Screen" menu. Now specify the display that will be the primary display. To do this, select its graphic image and activate the function "Make this screen basic".

5

Select the synchronous operation of the monitor andTV. It is recommended to use the item "Extend the screen". This allows you to simultaneously use the TV and monitor for various tasks. If you connected a TV to display a presentation, or you just want to use it instead of a monitor, then activate the "Duplicate screens" function. In this case, an identical image will be displayed on both displays.

You will need

• - HDNI cable;
• - SCART cable.

Instructions

1

The first way is through the HDNI connector. This is the most convenient and modern option. All televisions and media playerYou are currently equipped with this connector. In this case, only the HDNI cable is required to connect, which, as a rule, is included in the media playera.

2

So, connect both these devices with this cable. Wait for a while until the media player. The procedure usually takes no more than a few seconds. But maybe it will take a little longer.

3

Then go to settings. To output sound in the settings media playerand specify the dual-channel format "Dual Channel". To display a video image, in the technical specifications of the TV, find out which video mode it supports, and set the corresponding media playere. It may not be necessary, because in some cases the signal is automatically set. That's all for the HDNI connector.

4

The next connection method is a component signal. It is resorted to in the absence of an HDNI connector. Make sure, on your media playerThere is a component video output. If everything is ok, use a cable with three RCA connectors at both ends. This is nothing more than a "tulip". It is impossible to make a mistake in this case, since all the connectors have the same colors as the connectors.

5

It is also possible to connect media playerbut through SCART, which in its essenceis the standard of the connector, but not the standard for video transmission. To do this, you will need a SCART cable. It will transmit both sound and video image according to the RGB standard.

6

A few words about the possibility of connection media playerbut through the S-Video standard. Be sure to make sure that the corresponding connector is present on your device. In TVs and media playerMost often a four-pin connector is used. In the event that media playerThere is a SRART output, and S-Video on the TV, then use an adapter or a special cable.

7

And, at last, one more variant of connection - throughcomposite output. It is undesirable to resort to this method, since it is the least qualitative. With its help, you can check the device's operation at purchase. Well, at most, connect media player, if all of the above methods are not possible.

You will need

• - Apple TV prefix;
• - TV with HDMI input;
• - HDMI cable;
• - Ethernet cable.

Instructions

1

Gently remove the Apple TV console from thepackaging. In the set should be an instruction, a network cable for 220 volts (be sure to purchase the adapter under the euro outlet), remote control from aluminum (batteries are not included) and the set-top box itself. HDMI and Ethernet cable for the set-top box are purchased separately.

2

Connect Apple TV to your TV usingHDMI cable. There are no other ways to connect to the playback device, so the analog input on the TV will not work. Connect the Ethernet cable with one end to the set-top box, and the other to the access point. You can also set up a Wi-Fi connection after you turn on the console using the Settings menu.

3

Be sure to switch your TVreceiver into HDMI mode. After the first start-up of the set-top box, you will be asked to choose the interface language, as well as the password for Wi-Fi, if this connection is detected.

4

In the same menu, enter your details to enter theiTunes store, workgroup (network name) in a networked spin. In the settings menu there is also a function for blocking unwanted content. In general, access to iTunes is similar to accessing this service from your iPod, iPad, iPhone or MacBook.

5

To play media files from a computeror mobile device, open file access on it. On the console, select Media from the menu. If access is closed with a password, you will be required to enter it.

6

To view files from the Internet, for example from the Youtube website, select "Internet" in the menu.

7

Manufacturers ask without much need not to press the update button in the settings, since in this case you will get a basic firmware in which regional components will not be included.